Dell PowerVault DR6000 Manuel d'utilisateur télécharger pdf (Page 1)

Check for documentation and information updates on dell.com/support/manuals.

Always

read the updates ﬁ rst because they often supersede information in other documents.

Setting Up Your Dell DR6000 System

Before You Begin

An active network with available Ethernet cables and connections.•

If the system has a 1 GbE NIC, connect all NIC ports on the NIC daughter card. If the system has a 10 GbE •

NIC, connect the 10 GbE ports on the NIC daughter card. If the system has both 10 GbE and 1 GbE NIC’s

then by default the 1 GbE NIC will be disabled. If you want to modify the default setting, see

Dell DR Series

System Command Line Reference Guide.

NOTE: Use CAT6a copper cables with a 10 GbE NIC. If you have an enhanced small form-factor

pluggable (SFP+) NIC, use an Optical SFP+ or Twinax cabling.

Network values required are IP addressing, Network Mask, Default Gateway, DNS Suffix, Primary (and •

Optional) DNS server, and Host Name. If DHCP is selected, these values are populated based on your

DHCP configuration. If DHCP is not selected, the values must be manually configured.

NOTE: It is recommended for you to use static IP.

Default values for the DR6000 ar

e:•

Default Static System IP: - 10.77.88.99

NOTE: Default static system IP is used only when there is no DHCP server. The default IP can be used to

configure the system using a point to point NIC connection.

Subnet mask IP: - 255.0.0.0

Default iDRAC IP: - 192.168.0.120

NOTE: For iDRAC connection, the login name is root and password is calvin.

On the first boot, you must set up the network and the host name for the Dell DR6000 system.•

When you set up the system for the ﬁ

rst time, connect the Dell DR6000 system to a keyboard and monitor. •

After the operating system and network are conﬁ gured, the system can be managed using a remote

browser interface.

To set up the Dell DR6000 system, use an account with administrator privileges.•

Preinstallation Requirements

1. Install the Rails for the Dell DR6000 System

For information about installing the rails for the Dell DR6000 system, see the

Rack Installation Instructions

that shipped with the rail kit.

2. Install the Rails for the Dell MD1200 Expansion Units (Optional)

For information about installing the rails for the Dell MD1200 system, see the

Rack Installation Instructions

that shipped with the rail kit.

3. Rack the Dell DR6000 System

For information about setting up the Dell DR6000 system, see the

Dell DR6000 Systems Getting Started Guide

that shipped with the system.

4. Install the Cable Management Arm (CMA) (Optional)

For information about installing the CMA, see the

CMA Installation Instructions

that shipped with the CMA kit.

5. Cabling Your MD1200 Expansion Enclosure (Optional)

For information about cabling the Dell DR6000 system with your MD1200 expansion shelves, see Expansion Shelf Cabling in the

Dell DR Series System Administrator Guide.

6. Power on Your MD1200 Expansion Enclosure (Optional) and DR6000

NOTE: If you are using the MD1200 Expansion Enclosure, ensure that you power on MD1200 Expansion Enclosure before powering on the DR6000.

7. Log On to the System

The default user name is administrator and the default password is St0r@ge!

NOTE: You can log on to the DR console directly using KVM or iDrac Virtual Console.

8. Conﬁ gure the Network

The Initial System Conﬁ guration Wizard prompts you to conﬁ gure the system, when you log on for the ﬁ rst time. To conﬁ gure the network:

a. Type yes and press <Enter>.

b. Choose either DHCP or static IP addressing.

To select DHCP, type Yes at Would you like to use DHCP and press <Enter>. To select static IP addressing, type no and press <Enter>.

If you choose static IP addressing, you will be prompted to enter the static IP address. Enter the static IP address and press <Enter>.

For static IP address, enter a subnet mask, a default gateway address, a DNS su x, and a primary DNS address.

You are also asked if you want to conﬁ gure a secondary DNS address.

The Initial System Conﬁ guration Wizard displays a conﬁ rmation screen with all the values you entered in this step.

c. To change the default host name, type Yes and press <Enter>.

NOTE: The default host name is

DR6000-<Service Tag>

The Initial System Conﬁ guration Wizard displays a screen with the selected interface, IP address choice, host name for the Dell DR6000 system, and the values you set

during step b on conﬁ guring the network.

d. To accept the settings, type Yes and press <Enter>.

You have now completed your hardware and basic network conﬁ guration. For more information about setting up your system,

see

Dell DR Series System Administrator Guide

Installing the Dell DR6000 Hardware and Conﬁ guring the Network

WARNING: Before you set up and operate your Dell system, review the safety instructions that came with your system.

Dell Software License Agreement

Before using your system, read the Dell Software •

License Agreement that came with your system.

If you do not accept the terms of the agreement, •

call the customer assistance telephone number.

For customers in the United States, call

800-WWW-DELL (800-999-3355). For customers

outside the United States, visit

dell.com/contactdell.

Locating Your System Service Tag

Your system is identified by a unique Express •

Service Code and Service Tag number. The

Express Service Code and Service Tag are

found on the front of the system. Pull out the

information tag to view the Express Service

Code and Service Tag.

Save this information for future reference. This •

information is used by Dell to route support

calls to the appropriate personnel.

NOTE: The illustrations in this document are not

intended to r

epresent a speciﬁ c system.

Verifying Your Solution

Dell DR6000 includes:

System bezel•

Power cords (2)•

Power cord retention straps (2)•

Mounting rails (2)•

Cable management arm (optional)•

User documentation•

Important Updates

NOTE: After you complete setting up the Dell DR6000 system, navigate to dell.com/support, enter your system service tag, and select Get Drivers for any

software updates. Apply the updates before using the system for the ﬁ rst time.

To update the system software, download the • DR6000 Upgrade Manager File from dell.com/support/downloads and apply the upgrade

using the web console or CLI.

To reinstall the system, download the • Dell DR6000 Restore Manager from dell.com/support/downloads.

NOTE: For information about upgrading the DR Series system software and restore manager, see the

Dell DR Series System Administrator Guide

Documentation

The following documents are available for you at dell.com/powervaultmanuals:

The •

Getting Started Guide

also shipped with your system provides an overview of setting up your system, and technical specifications.

The rack documentation included with your rack solution describes how to install your system into a rack, if required.•