Dell E6330 Manuel du propriétaire Page 1

Dell Latitude E6330Owner's ManualRegulatory Model: P19SRegulatory Type: P19S001

10

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

Removing the ExpressCard1. Follow the procedures in Before Working Inside Your Computer.2. Press in on the ExpressCard to release it from the computer

Installing the Battery1. Slide the battery into its slot until it clicks into place.2. Follow the procedures in After Working Inside Your Computer.Rem

Installing the SIM Card1. Slide the SIM card into its compartment.2. Install the battery.3. Follow the procedures in After Working Inside Your Compute

5. Remove the screw that secures the hard-drive bracket to the hard drive.6. Pull the hard-drive bracket out of the hard drive.7. Remove the hard-driv

Removing the Optical Drive1. Follow the procedures in Before Working Inside Your Computer.2. Remove the battery.3. Push in the eject handle on the opt

7. Remove the screws that secure the drive-latch bracket to the optical drive.8. Remove the drive-latch bracket from the optical drive.9. Pull and rem

3. Tighten the screw to secure the optical-drive latch to the optical drive.4. Secure the drive latch to the optical drive.5. Tighten the screw to sec

4. Pry the keyboard trim along the sides and bottom.5. Lift up to remove the keyboard trim from the unit.Installing the Keyboard Trim1. Align the keyb

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

5. Remove the screws that secure the keyboard to palmrest assembly.6. Lift and turn the keyboard to access the keyboard cable.7. Disconnect the keyboa

9. Disconnect the keyboard cable from the keyboard.10. Remove the keyboard cable from the keyboard.Installing the Keyboard1. Connect the keyboard cabl

Removing the Wireless Local Area Network (WLAN) Card1. Follow the procedures in Before Working Inside Your Computer.2. Remove the battery.3. Remove th

6. Remove the screw that secures the bluetooth module to the computer.7. Remove the bluetooth module from the computer.8. Disconnect the bluetooth cab

3. Place the bluetooth card in its location in the computer.4. Tighten the screw to secure the bluetooth card to the system board5. Install:a) base co

Removing the Coin-Cell Battery1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) batteryb) base cover3. Disconnect the c

e) optical drivef) base coverg) keyboard trimh) keyboardi) bluetooth module3. Remove the screws that secure the palmrest assembly to the base of the c

7. Disconnect the power LED cable from the system board.8. Lift the palmrest up and away from the computer.Installing the Palmrest1. Align the palmres

e) optical drivef) hard driveg) batteryh) ExpressCardi) SD card6. Follow the procedures in After Working Inside Your Computer.Removing the Media Board

Installing the Media Board1. Place the media board in its compartment.2. Tighten the screws to secure the media board.3. Connect the media-board cable

Contents1 Working on Your Computer... 7Before Work

4. Remove the screws that secure the ExpressCard cage to the computer.5. Remove the ExpressCard cage from the computer.Installing the ExpressCard Cage

j) SD card5. Follow the procedures in After Working Inside Your Computer.Removing the Speakers1. Follow the procedures in Before Working Inside Your C

6. Remove the speakers from the computer.Installing the Speakers1. Align the speakers to their original position and tighten the screws to secure the

f) base coverg) keyboard trimh) keyboardi) bluetooth modulej) palmrest3. Remove the screws that secure the display-hinge covers to the computer.4. Rem

a) SD cardb) ExpressCardc) batteryd) hard drivee) optical drivef) base coverg) keyboard trimh) keyboardi) bluetooth modulej) palmrest3. Release the an

7. Lift up and remove the LVDS support bracket.8. Disconnect the LVDS cable from the system board.9. Pull the antenna cables from the opening on the s

Installing the Display Assembly1. Route the antennae cables through the opening on the system board.2. Connect the LVDS cable to the system board.3. T

m) display assembly3. Disconnect the coin-cell battery cable from the system board.4.Disconnect the ExpressCard cable from the system board.5. Disconn

8. Disconnect the power-connector cable from the system board.9. Remove the system board from the computer.Installing the System Board1. Connect the p

f) keyboardg) keyboard trimh) base coveri) optical drivej) hard drivek) batteryl) ExpressCardm) SD card5. Follow the procedures in After Working Insid

Installing the ExpressCard Cage...

5. Remove the heat sink from the system board.Installing the Heat Sink1. Place the heat sink into its original position on the system board.2. Tighten

k) media boardl) display hinge coversm) display assemblyn) system board3. Remove the screw that secures the power connector port to the computer.4. Re

d) media boarde) palmrestf) bluetooth moduleg) keyboardh) keyboard trimi) base coverj) optical drivek) hard drivel) batterym) ExpressCardn) SD card5.

Installing the I/O Board1. Place the I/O board in its compartment.2. Tighten the screws to secure the I/O board.3. Install:a) system boardb) display a

5. Remove the display bezel from the display assembly.Installing the Display Bezel1. Place the display bezel onto the display assembly.2. Starting fro

5. Flip and place the display panel over.6. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel.7. Remove the

Removing the Camera and Microphone Module1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) display bezel3. Remove

a) display bezelb) battery5. Follow the procedures in After Working Inside Your Computer.Removing the LED Board1. Follow the procedures in Before Work

7. Remove the LED board from the LED-board support plate.Installing the LED Board1. Tighten the screw to secure the LED board to the LED board support

j) palmrestk) media boardl) display hinge coversm) display assemblyn) display bezelo) display panelp) power LED board3. Remove the screw that secures

Enhanced Pre-Boot System Assessment (ePSA) Diagnostics...69Device Status L

7. Remove the screw that secures the right display-hinge wall to the display assembly.8. Slide and remove the right display-hinge wall out of the disp

i) keyboardj) keyboard trimk) base coverl) optical drivem) hard driven) batteryo) ExpressCardp) SD card5. Follow the procedures in After Working Insid

5. Repeat steps 3 and 4 to remove the right display hinge.Installing the Display Hinges1. Place both the display hinges on the panel.2. Tighten the sc

j) palmrestk) media boardl) display hinge coversm) display assemblyn) display bezelo) display panelp) power LED boardq) display hinge walls3. Remove t

Installing the LVDS and Camera Cable1. Route the LVDS and camera cable on the display assembly.2. Fix the adhesive the tape to secure the cable.3. Con

3Docking Port InformationThe docking port is used for connecting the laptop to a docking station (optional).1. Docking Port55

56

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Keys Navigation<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.Spacebar Expands or co

Option Description• Disabled• Enabled• Enabled w/PXE (Default Setting)Parallel Port Allows you to define and set how the parallel port on the docking

6

Option Description• Enable SMART Reporting - This option is disabled by default.USB Configuration Allows you to define the USB configuration. The opti

Table 4. VideoOption DescriptionLCD Brightness Allows you to set the panel brightness when the ambient sensor is Off.Optimus Allows you to enable or d

Option DescriptionDefault Setting: Enable CPU XD SupportComputrace Allows you to activate or disable the optional Computrace software The options are

Option DescriptionHyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.Default Setting: EnabledTable 7. Power Mana

Option Description• Custom Charge — you can set the percentage to which the battery must charge .NOTE: All charging modes may not be available for all

Table 9. Virtualization SupportOption DescriptionVirtualization This option specifies whether a Virtual Machine Monitor (VMM) can utilize the addition

Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensur

To enter a system setup, press <F2> immediately after a power-on or re-boot.1. In the System BIOS or System Setup screen, select System Security

68

5DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

Turns on steadily or blinks to indicate battery charge status.Turns on when wireless networking is enabled.The device status LEDs are usually located

6Technical SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. F

AudioInternal high-definition audioExternal microphone-in/stereo headphones/external speakers connectorSpeakers twoInternal speaker amplifier 1 W (RMS

DisplayLatitude E6330 13.3"Dimensions:Latitude E6230Height 300.90 mm (11.84 inches)Width 180.00 mm (7.08 inches)Diagonal 317.30 mm (12.49 inches)

Battery• 6-cell (58 WHr) Lithium-ion batteryDimensions:3-cellDepth 29.97 mm (1.18 inches)Height 19.80 mm (0.78 inch)Width 208.00 mm (8.19 inches)6-cel

PhysicalLatitude E6230 Latitude E6330Height 22.40 mm to 24.70 mm (0.88 inch to 0.97 inch)25.40 mm to 30.10 mm (1 inch to 1.19 inches)Width 309.00 mm (

76

7Contacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill,

NOTE: To avoid damaging the system board, you must remove the main battery before you service the computer.7. Remove the main battery.8. Turn the comp

After Working Inside Your ComputerAfter you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turn