Dell P2213 Guide de l'utilisateur

Dell™ P1913/P1913S/P2213 Monitor User's GuideSetting the display resolution Information in this document is subject to change without notice.© 20

*[P1913]/[P1913S]/[P2213] color gamut (typical) is based on CIE1976 (83%) and CIE1931 (72%) test standards. Resolution SpecificationsModel P1913 P1913

P1913SDisplay ModeHorizontal Frequency(kHz)Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (Horizontal/Vertical)VESA, 720 x 400 31.5 70.0 28.

Model P1913/P1913S/P2213Video input signalsAnalog RGB, 0.7 Volts +/- 5%, positive polarity at 75 ohm input impedanceDigital DVI-D TMDS, 600 mV for eac

Depth 58.5 mm (2.30 inches) 59.3 mm (2.33 inches) 59.8 mm (2.35 inches)Stand dimensionsHeight(extended)401.2 mm (15.80 inches) 401.2 mm (15.80 inches)

Operating 3,048 m (10,000 ft) maxNon-operating 10,668 m (35,000 ft) max 10,668 m (35,000 ft) max 10,668 m (35,000 ft) maxThermal dissipation143.31 BTU

* Zero power consumption in OFF mode can only be achieved by disconnecting the main cable from the monitor.** Maximum power consumption with max lum

DVI ConnectorPinNumber24-pin Side of the Connected Signal Cable1 TMDS RX2-2 TMDS RX2+3 TMDS Ground4 Floating5 Floating6 DDC Clock7 DDC Data8 Floatin

20 Floating21 Floating22 TMDS Ground23 TMDS Clock+24 TMDS Clock- DisplayPort ConnectorPin Number 20-pin Side of the ConnectedSignal Cable1 ML0(p)2 GND

15 AUX(p)16 GND17 AUX(n)18 HPD19 Re-PWR20 PWR Plug and Play CapabilityYou can install the monitor in any Plug and Play-compatible system. The monitor

Pin Number 4-pin Side of the Connector1DMU2 VCC3DPU4GND USB Downstream ConnectorPin Number 4-Pin Side of the Signal Cable1VCC2DMD3DPD4GNDUSB Ports1 up

Dell™ P1913/P1913S/P2213 Monitor User's GuideAbout Your MonitorSetting Up the MonitorOperating the MonitorTroubleshootingAppendixNotes, Cautions,

take a few seconds to resume normal functionality.LCD Monitor Quality and Pixel PolicyDuring the LCD Monitor manufacturing process, it is not uncommon

Back to Contents PageSetting Up the MonitorDell™ P1913/P1913S/P2213 Monitor User's Guide Attaching the Stand Connecting the Monitor Organizing

Connecting Your Monitor WARNING: Before you begin any of the procedures in this section, follow the Safety Instructions.To connect your monitor to the

Connecting the white DVI cableConnecting the blue VGA cableConnecting the black DisplayPort cable

CAUTION: The graphics are used for the purpose of illustration only. Appearance of the computer may vary.Connecting the USB cableAfter you have compl

Organizing Your CablesAfter attaching all necessary cables to your monitor and computer, (See Connecting Your Monitor for cable attachment,) organize

CAUTION: Do not use with any device other than the Dell Soundbar. NOTE: The Soundbar power connector (+12 V DC output) is for the optional Dell Soun

2. Press and hold the stand release button.3. Lift the stand up and away from the monitor.Wall Mounting (Optional)(Screw dimension: M4 x 10 mm).Refe

Back to Contents PageOperating the MonitorDell™ P1913/P1913S/P2213 Monitor User's Guide Power On the Monitor Using the Front Panel Controls Us

The following table describes the front panel buttons:Front Panel Button Description1Shortcutkey/PresetModesUse this button to choose from a list of p

Back to Contents PageAbout Your MonitorDell™ P1913/P1913S/P2213 Monitor User's GuidePackage ContentsProduct FeaturesIdentifying Parts and Control

5Power (with power lightindicator)Use the Power button to turn the monitor On and Off.The blue LED indicates the monitor is On and fully functional.

Using the On-Screen Display (OSD) Menu Accessing the Menu SystemNOTE: If you change the settings and then either proceed to another menu or exit the

orMain Menu for digital (DP) input

NOTE: Auto Adjust is only available when you use the analog (VGA) connector.NOTE: For P1913, the maximum resolution is 1440 x 900 @ 60Hz. For P1913S,

Brightness Brightness adjusts the luminance of the backlight.Press the button to increase the brightness and press the button to decrease the b

Auto Adjust Even though your computer recognizes your monitor on startup, the Auto Adjustment function optimizes the display settings for use with y

Select the DVI-D input when you are using the Digital (DVI) connector. Press to select the DVI input source.DisplayPortSelect the DisplayPort input

Preset Modes When you select Preset Modes, you can choose Standard, Multimedia, Movie, Game, Text, Warm, Cool or Custom Color from the list.Standard:

HueThis feature can shift the color of the video image to green or purple. This is used to adjust the desired flesh tone color. Use or toadjust th

NOTE: Aspect Ratio is not available in P1913S. Aspect Ratio Adjust the image ratio to Wide 16:10, 5:4 or 4:3.NOTE: Aspect Ratio is not available in P

StandPower CableVGA Cable (Attached to the monitor)DVI CableUSB upstream cable (enables the USB ports on the monitor)

NOTE: Pixel Clock and Phase adjustments are only available for "VGA" input. Dynamic Contrast Dynamic Contrast adjusts the contrast ratio to

Lock function – Either soft lock (through the OSD menu) or hard lock (press and hold the button above the power button for 10 seconds)Unlock function–

Factory Reset Reset all OSD settings to the factory preset values.Personalize Users can choose a feature from "Preset Modes", "Bright

NOTE: This monitor has a built-in feature to automatically calibrate the brightness to compensate for LED aging.OSD Warning MessagesWhen the Energy S

When the monitor does not support a particular resolution mode, you will see the following message:

This means that the monitor cannot synchronize with the signal that it is receiving from the computer. See Monitor Specifications for the Horizontal a

Activate the computer and wake up the monitor to gain access to the OSD.If you press any button other than the power button, one of the following mess

Setting the Maximum ResolutionTo set the maximum resolution for the monitor:Windows Vista® or Windows® 7:1. Right-click on the desktop and select Per

4 Power indicatorUsing the Tilt, Swivel, and Vertical ExtensionNOTE: This is applicable for a monitor with a stand. When any other stand is bought, pl

Rotating the MonitorBefore you rotate the monitor, your monitor should be fully vertically extended (Vertical Extension) and fully tilted (Tilt) up to

Drivers and Documentation mediaQuick Setup GuideProduct and Safety Information GuideProduct FeaturesThe Dell Professional P1913/P1913S/P2213 flat pane

NOTE: To use the Display Rotation function (Landscape versus Portrait view) with your Dell computer, you require an updated graphics driver that is no

Back to Contents PageTroubleshootingDell™ P1913/P1913S/P2213 Monitor User's Guide Self-Test Built-in Diagnostics Common Problems Product Spec

4. This box also appears during normal system operation, if the video cable becomes disconnected or damaged.5. Turn off your monitor and reconnect t

4. Carefully inspect the screen for abnormalities.5. Press Button 4 on the front panel again. The color of the screen changes to red.6. Inspect the

Synchronization Problems Screen is scrambled or appears torn Reset the monitor to Factory Settings.Perform Auto Adjust via OSD.Adjust Phase and Pixel

High Speed USB 2.0 interface is slow. High Speed USB 2.0 peripheralsworking slowly or not working at allCheck that your computer is USB 2.0-capable.So

Back to Contents PageAppendixDell™ P1913/P1913S/P2213 Monitor User's Guide Safety Instructions FCC Notice (U.S. Only) and Other Regulatory Info

Back to Contents PageSetting Up Your MonitorDell™ P1913/P1913S/P2213 Monitor User's GuideSetting the display resolutionFor maximum display perfor

Back to Contents PageSetting Up Your MonitorDell™ P1913/P1913S/P2213 Monitor User's GuideIf you have a Dell™ desktop or a Dell™ portable computer

Back to Contents PageSetting Up Your MonitorDell™ P1913/P1913S/P2213 Monitor User's GuideIf you have a non Dell™ desktop, portable computer, or g

Identifying Parts and ControlsFront ViewFront panel controls Label Description1Function buttons (For more information, see Operating theMonitor)2 Powe

Back View Back View with monitor standLabel Description Use1VESA mounting holes (100 mm x 100 mm- behind attached VESA Plate)Wall mount monitor using

Side ViewBottom View Bottom view without monitor standLabel Description Use1 AC power cord connector Connect the power cable.2 DC power connector fo

5 DVI connector Connect your computer DVI cable.6 USB upstream portConnect the USB cable that came with your monitor to the monitor and thecomputer. O