Dell 7010 Manuel du propriétaire

Dell OptiPlex 9010/7010 Ultra Small Form FactorOwner's ManualRegulatory Model: D01URegulatory Type: D01U003

4. Lift the drive cage using the handle and flip over the drive cage.5. Lift the drive cage and remove the data cable and power cable from the back of

6. Remove the drive cage from the computer.Installing the Drive Cage1. Place the drive cage on the edge of the computer near the front bezel to allow

Removing the Optical Drive1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) coverb) front bezelc) drive cage3. Press the op

Installing the Hard Drive1. Insert the hard drive into the hard-drive bracket.2. Slide the hard drive back into the drive cage.3. Tighten the screws t

Memory Module GuidelinesTo ensure optimal performance of your computer, observe the following general guidelines when configuring your system memory:•

Installing the Memory1. Align the notch on the memory-card with the tab on the system-board connector.2. Press down on the memory module until the rel

5. Install the front bezel.6. Install the cover.7. Follow the procedures in After Working Inside Your Computer.Removing the System Fan1. Follow the pr

5. Remove the fan from the chassis.Installing the System Fan1. Place the system fan in the chassis.2. Tighten the screws that secure the fan to the ch

4. Pull out the speaker cable from beneath the system fan cable and Wireless Local Area Network (WLAN) antennae (if installed).5. Release the latch an

Installing the Internal Speaker1. Place the speaker on the appropriate location of the rear end of the chassis.2. Rotate until the latch is secured in

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

4. Remove the screw and pull the power switch board out of the computer.Installing the Power Switch1. Slide the power-switch through the front of the

4. Remove the screws that secures the I/O panel to the computer.5. Slide the I/O panel towards the left of the computer to release it and pull the I/O

3. Use a screwdriver to tighten the screws to secure the Input/Output panel to the computer.4. Connect the Input/Output panel data cable to the system

5. Remove the screws that secures the power supply to the chassis.6. Slide the power supply inward and lift the power supply unit out of the computer.

4. Connect the cables to the system board.5. Install the heat sink.6. Install the intrusion switch.7. Install the drive cage.8. Install the front beze

4. Press the release lever down and outward to release the fan retention hook.5. Lift the top portion of the heat sink/fan assembly.6. Loosen the capt

Lay the assembly with the fan facing downward, and with the thermal grease facing upward.Installing the Heat Sink1. Place the heat sink into the chass

Installing the Processor1. Insert the processor into the processor socket. Ensure the processor is properly seated.2. Press the release lever down and

5. Remove the screws that secure the system board to the chassis.6. Remove the 7–mm hex screw from the system board.28

7. Slide the system board towards the front of the computer and remove.29

ContentsNotes, Cautions, and Warnings...21 Working on

System Board LayoutThe following image displays the system board layout.1. memory module connectors 2. internal speaker cable3. USB audio connector 4.

7. Install the memory.8. Install the processor.9. Install the heat sink.10. Install the power supply.11. Install the system fan.12. Install the drive

32

3System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Keys Navigation<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.Spacebar Expands or co

Table 3. System ConfigurationOption DescriptionIntegrated NIC Allows you to enable or disable the integrated network card. You can set the integrated

Option DescriptionFor Mini-Tower, Desktop, Small Form Factor the options are:• Enable Boot Support• Enable Rear Dual USB Ports• Enable Rear Quad USB P

Option Description• Admin Password Min• Admin Password Max• System Password Min• System Password MaxPassword Bypass Allows you to bypass the System Pa

Table 5. PerformanceOption DescriptionMulti Core Support Specifies whether the process will have one or all cores enabled. The performance of some app

Option DescriptionThis option is disabled by default.Fan Control Override Controls the speed of the system fan. This option is disabled by default.NOT

Installing the Heat Sink...

Option Description• Enable Intel Virtualization Technology for Direct I/O - This option is enabled by default.Trusted Execution This option specifies

Option DescriptionNOTE: This field is only relevant when the Integrated NIC control in the System Configuration group is set to Enabled with ImageServ

Follow the instructions on the screen.Jumper SettingsTo change a jumper setting, pull the plug off its pin(s) and carefully fit it down onto the pin(s

4. Type the system password that you entered earlier and click OK.5. Select Setup Password, type your system password and press <Enter> or <T

10. Install the cover.11. Follow the procedures in After Working on Your Computer.12. Power-on the computer.13. Go to the system setup, and assign a n

4DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

46

5Troubleshooting Your ComputerYou can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the op

Amber LED State Description3,7 some other failure with messages on screenBeep CodeThe computer can emit a series of beeps during start-up if the displ

Error Message DescriptionGate A20 failure One or more memory modules may be faulty or improperly seated. Reinstall the memory modules and, if necessar

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

Error Message DescriptionPlug and play configuration error The computer encountered a problem while trying to configure one or more cards.Read fault T

6SpecificationsNOTE: Offerings may vary by region. For more information regarding the configuration of your computer, click Start (Start icon) → Help

Feature Specification• Intel HD Graphics 2500/4000 (i3/i5/i7 DC/QC Intel 7 Series Express Chipset CPU-GPU Combo)Discrete PCI Express x16 graphics adap

Feature SpecificationPCI Express x1:Mini-Tower up to three full-height cardsDesktop up to three low-profile cardsSmall Form Factor up to two low-profi

Feature SpecificationNetwork Adapter one RJ45 connectorSerial one 9-pin connector; 16550 C compatibleParallel one 25-pin connector (optional for mini-

Feature SpecificationMini-Tower four 7-pin connectorsDesktop three 7-pin connectorsSmall Form Factor three 7-pin connectorsUltra Small Form Factor two

Feature SpecificationLink integrity light on integrated network adapterGreen — a good 10 Mbps connection exists between the network and the computer.O

Table 28. EnvironmentalFeature SpecificationTemperature range:Operating 10 °C to 35 °C (50 °F to 95 °F)Storage –40 °C to 65 °C (–40 °F to 149 °F)Relat

58

7Contacting Dell To contact Dell for sales, technical support, or customer service issues:1. Visit support.dell.com. 2. Verify your country or region

CAUTION: Before touching anything inside your computer, ground yourself by touching an unpainted metal surface, such as the metal at the back of the c

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

Installing the Cover1. Place the cover on the computer.2. Slide the computer cover towards the front of the chassis until it is fully engaged.3. Tight

Installing the Front Bezel1. Insert the hooks along the bottom edge of the front panel into the slots on the chassis.2. Rotate the bezel toward the co