Dell Tower 5810 + U2713HM Manuel du propriétaire

Dell Precision Tower 5810Owner's ManualRegulatory Model: D01TRegulatory Type: D01T006

22. mechanical slot23. power cable connector24. power-supply unit (PSU) release latchFigure 2. Inside View of T5810 Computer1. heatsink with integrate

Figure 3. Inside View of T5810 Computer1. PCIe-card retention2. internal speaker3. power-supply unit4. mother boardRemoving the Power Supply Unit (PSU

Installing the Power Supply Unit (PSU)1. Hold the PSU handle and slide the PSU into the computer.2. Follow the procedures in After Working Inside Your

Installing the Computer Cover1. Place the computer cover on the chassis.2. Press down on the computer cover until it clicks into place.3. Follow the p

4. Perform the following steps as shown in the illustration:a. Disconnect the power cables from the system board [1].b. Remove the screws securing the

Removing the Front Bezel1. Follow the procedures in Before Working Inside Your Computer.2. Remove the computer cover.3. Gently pry the front bezel ret

4. Unthread the cables from the latches.5. Press on the clasp to release the latch holding the cables on the side of the optical-drive cage.6. Press d

7. Lift up the release latch on top of the optical-drive cage.8. Holding the release latch, slide the optical-drive cage from the optical-drive compar

10. Remove the screws that secure the optical drive to the optical-drive cage.11. Remove the optical drive from the optical-drive cage.Installing the

4. Press in on the latches on either side of the hard-drive bracket.5. Slide the hard drive out of the compartment.19

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

6. If a 2.5–inch hard drive is installed, remove the screws and lift up the drive to remove it from the hard-drive caddy.7. If a 3.5–inch hard drive i

Installing the Hard Drive 1. If a 3.5–inch hard drive is installed on the computer, place the hard drive and press in on the latches of the hard-drive

Installing the Speaker1. Replace the speaker and fix the clasp.2. Connect the speaker cable to the system board.3. Install the computer cover.4. Follo

Installing the HDD Thermal SensorNOTE: The HDD thermal sensor is an optional component and your computer may not ship with it.1. Connect the HDD therm

5. Disconnect the cables to release the I/O panel.6. Remove the screws which secure the I/O panel to the I/O panel cage.7. Remove the I/O panel from t

Installing the Input/Output (I/O) Panel1. Replace the I/O panel in the I/O panel cage.2. Tighten the screw securing the I/O panel to the I/O panel cag

5. Repeat Step 3 and Step 4 to remove the second memory shroud module from the computer.Installing the Memory Shroud1. Install the memory shroud modul

Installing the Memory1. Insert the memory module into the memory socket.2. Press down on the memory module until the securing clips secure the memory

4. Press down the latch and pull the PCI card away from the computer.Installing the PCI Card1. Push the expansion card into the card slot and secure t

b. PCIe cards3. Perform the following steps as shown in the illustration:a. Unthread the cable from the clips [1].b. Press and slide the latch out to

Contents1 Working on Your Computer...5Before Working Inside Your Computer

4. Remove the screw that secures metal plate to the system fan.5. Press the latches on either side of the metal plate to release it.30

6. Lift the metal plate out of the chassis.7. Remove the screws that secure the drive bay.31

8. Disconnect the system-fan cables from the system board.9. Perform the following steps as shown in the illustration:a. Remove the screws that secure

CAUTION: Using excessive force may damage the grommets.11. Remove the system fans from the system-fan assembly.Installing the System-Fan Assembly1. Pl

10. Follow the procedures in After Working Inside Your Computer.Removing the Heatsink Assembly1. Follow the procedures in Before Working Inside Your C

Installing the Heatsink Fan1. Slide the heatsink fan into heatsink assembly.2. Install the screws that secure the heatsink fan to the heatsink assembl

NOTE: Damaging pins during removal of the processor can cause damage to the processor.4. Repeat the above steps to remove the second processor (if ava

1. PCI slot (slot 6) 2. PCIe x16 slot (PCIe 2.0 wired as x4) (slot 5)3. PCIe 3.0 x16 slot (slot 4) 4. PCIe 2.0 x1 slot (slot 3)5. PCIe 3.0 x16 slot (s

Removing the System Board1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a. computer coverb. optical drivec. graphics card a

5.a. Slide the system board towards front direction [1].b. Tilt the system board [2].6. Lift the system board in an upward direction and remove it fro

Removing the Heatsink Assembly... 34Installing the

Installing the System Board1. Align the system board to the port connectors on the back of the chassis and place the system board in the chassis.2. Ti

3Additional InformationThis section provides information for the additional features that are part of your computer.Memory Module GuidelinesTo ensure

42

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Table 1. Navigation KeysKeys NavigationUp arrow Moves to the previous field.Down arrow Moves to the next field.<Enter> Allows you to select a va

Option Description• Enable Legacy Option ROMs (Default)Date/Time Allows you to set the date and time. The changes to the system date and time takes ef

Option DescriptionNOTE: SATA is configured to support RAID mode. No SATA operation support in Tower 7910.Tower 7910Allows you to configure the interna

Option DescriptionSAS RAID Controller (Tower 7910 only)Allows you to control the operation of the integrated SAS RAID HDD controller.• Enabled (Defaul

Option Description• SLOT2_CPU2 (Tower 7910 only)Table 5. SecurityOption DescriptionStrong Password Allows you to enforce the option to always set stro

Option Description• Disabled (Default)• EnabledExpert Key Management Allows you to enable or disable Custom Mode Key Management.• Disabled (Default)Ta

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

Option DescriptionDefault Setting: The option is disabled.Intel TurboBoost Allows you to enable or disable the Intel TurboBoost mode of the processor.

Option DescriptionUSB Wake Support Allows you to enable USB devices to wake the system from standby.• Enable USB Wake SupportDefault Setting: The opti

Option Description• Trusted Execution - This option is disabled by default.Table 11. MaintenanceOption DescriptionService Tag Displays the service tag

6. Select your computer model and the Product Support page of your computer appears.7. Click Get drivers and click View All Drivers.The Drivers and Do

• Only lower case letters are valid, upper case letters are not allowed.• Only the following special characters are allowed: space, (”), (+), (,), (-)

6. Connect the computer to the electrical outlet and power-on the computer.7. Power-off the computer and disconnect the power cable from the electrica

5DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

6Troubleshooting Your ComputerYou can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the op

Check the PSU cabling to Motherboard to make sure that all cables are installed correctly.2,3A possible Motherboard, Memory, or CPU failure has occurr

at a time) until you have identified all modules without error. If available, install working memory of the same type into your computer.3,4Power conn

CAUTION: To disconnect a network cable, first unplug the cable from your computer and then unplug the cable from the network device.3. Disconnect all

Table 16. Errors that halt your computer completelyError MessageError! Non-ECC DIMMs are not supported on this system.Alert! Processor cache size is m

Error MessageAlert! Memory related failure detected.Alert! Correctable memory error has been detected in memory slot DIMMx.Warning: Non-optimal memory

7Technical SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. F

Table 23. AudioFeature SpecificationIntegrated Realtek ALC3220 audio codecTable 24. NetworkFeature SpecificationTower 5810 Intel i217Table 25. Expansi

Feature Specification• supports one 5.25–inches SATA optical device or supports one 3.25–inches SATA HDD device• supports one media card reader• suppo

Feature SpecificationPCI Express x4Tower 5810 two 164-pin connectorsPCI Express x16Tower 5810 two 164-pin connectorsPCI 2.3 one 124-pin connectorFront

Table 30. PowerFeature SpecificationVoltage 100 VAC to 240 VACWattageTower 5810 685 / 425 W (input voltage of 100 VAC – 240 VAC)Maximum heat dissipati

Feature SpecificationAirborne contaminant level G1 as defined by ISA-S71.04-198567

8Contacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill,

2. Click the arrow in the lower-right corner of the Start menu as shown below, and then click Shut Down .2. Ensure that the computer and all attached

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

System OverviewFigure 1. Front and Back View of T5810 Computer1. microphone connector2. power button/Power light3. hard-drive activity light4. USB 3.0