Dell Broadcom NetXtreme Family of Adapters Manuel d'utilisateur Page 164
- Page / 175
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Troubleshooting: Broadcom NetXtreme BCM57XX User Guide
file:///C|/Users/Nalina_N_S/Documents/NetXtreme/English/trouble.htm[9/5/2014 3:32:22 PM]
tool.
5. Verify that the IP address is correct for the network to which the adapter(s) is connected.
NetWare
Ping an IP host on the network to verify connection has been established:
From the command line, type ping IP address, and then press ENTER.
The ping statistics that are displayed indicate whether the network connection is working or not.
Linux
To verify that the Ethernet interface is up and running, run ifconfig to check the status of the Ethernet interface. It is
possible to use netstat -i to check the statistics on the Ethernet interface. Go to Linux Driver Software for information on
ifconfig and netstat.
Ping an IP host on the network to verify connection has been established:
From the command line, type ping IP address, and then press ENTER.
The ping statistics that are displayed indicate whether the network connection is working or not.
Software Problems and Solutions
How to Add a Third-Party OEM Network Adapter to a RIS Installation
Problem: An error is encountered when attempting to load the Broadcom device driver for a 32-bit version of Windows XP,
or later operating system, using a Windows 2000 Remote Installation Server: File b57w2k.sys caused an unexpected error
(21) at line 3752 in d:\xpsp1\base\boot\setup\setup.c.
Solution: A modification to the b57win32.inf file can be made to allow for the installation to complete successfully. This will
be in conjunction with instructions from the Microsoft Knowledge Base Article 315279 that describe "How to Add Third-Party
OEM Network Adapters to RIS Installations."
Requirement: The Windows 2000 Server must be running Service Pack 3 or later.
1. Obtain the latest driver for your Broadcom adapter. The driver files included for the Broadcom 57xx adapter are
b57win32.inf, b57win32.cat, and b57xp32.sys.
2. Create a copy of the b57win32.inf and b57xp32.sys files and save them in a separate folder called RIS. This allows you
to distinguish the duplicate files from the originals.
3. For the b57win32.inf file located in the RIS folder, make the following change using a text editor such as Notepad:
a. Locate [Manufacturer] within the file.
b. Review the line below which reads: %BRCM% = Broadcom, NTx86.5.1, NTamd64.
c. Modify that line to read: %BRCM% = Broadcom.NTx86.5.1, NTamd64. (The change replaces the comma
and the space after "Broadcom" with a period.
d. Save the file.
4. On the RIS server, copy the b57win32.inf and b57xp32.sys files from the RIS folder to the
RemoteInstall\Setup\Language\Images\Dir_name\i386 folder. This allows Setup to use the driver during the text-mode
portion of the installation.
a. At the same level as the i386 folder on the RIS image, create a $oem$ folder. Use the recommended structure:
\$oem$\$1\Drivers\Nic
b. Copy the original b57win32.inf, b57xp32.sys, and b57win32.cat driver files to this folder.
c. Make the following changes to the .sif file that is used for this image installation:
[Unattended]
OemPreinstall = yes
OemPnpDriversPath = \Drivers\Nic
5. Stop and then restart the Remote Installation service on the RIS server by typing the following from a command
prompt:
net stop binlsvc
- Broadcom NetXtreme 1
- BCM57XX User Guide 1
- Functional Description 3
- Features 3
- Types of Teams 7
- Link Aggregation (802.3ad) 7
- SLB (Auto-Fallback Disable) 8
- LiveLink™ Functionality 8
- VLAN Overview 10
- Adding VLANs to Teams 11
- BASP Subagent 12
- BASP Extensible-Agent 13
- System Requirements 14
- Safety Precautions 14
- Preinstallation Checklist 15
- Installing the Adapter 15
- Connecting the Network Cables 15
- Overview 18
- Setting Up the BIOS 19
- Linux Red Hat PXE Server 19
- DOS UNDI/Intel APITEST 20
- Configuring the iSCSI Target 21
- Enabling CHAP Authentication 24
- Configuring the DHCP Server 26
- Locally Administered Address 32
- Troubleshooting iSCSI Boot 33
- Modifying the Startup Disk 35
- Limitations 40
- Packaging 40
- Network Installations 41
- Patching PCI Files (Optional) 42
- Driver Messages 42
- Teaming with Channel Bonding 43
- Driver Defaults 45
- Using the Installer 47
- Using Silent Installation 48
- Modifying the Driver Software 49
- Removing the Device Drivers 50
- WinPE 2.0 51
- WinPE 3.1 52
- Using WS-MAN 55
- Using WMI 62
- Teaming Concepts 66
- Description of Teaming Types 67
- Software Components 69
- Hardware Requirements 69
- Switching Hub 70
- Repeater Hub 70
- Selecting a Team Type 71
- Teaming Mechanisms 72
- Outbound Traffic Flow 73
- Protocol Support 74
- Switch-Dependent 76
- Applications 76
- Configuration Recommendations 76
- Supported Teaming Speeds 78
- Checksum Offload 79
- IEEE 802.1p QoS Tagging 79
- Large Send Offload 79
- Jumbo Frames 79
- IEEE 802.1Q VLANs 79
- Wake on LAN 80
- Teaming Across Switches 80
- Spanning Tree Algorithm 82
- Topology Change Notice (TCN) 83
- Port Fast/Edge Port 83
- Layer 3 Routing/Switching 84
- Application Considerations 85
- Teaming and Network Backup 88
- Load Balancing and Failover 89
- Fault Tolerance 90
- Teaming Configuration Tips 91
- Frequently Asked Questions 92
- Event Log Messages 95
- BCM57XX User Guide 98
- Filter View 99
- Discovery Wizard 100
- Manage Targets Wizard 100
- Manage iSNS Servers 101
- Manage Discovery Portals 101
- Boot Configuration Wizard 101
- Managing the Host 102
- Information Tab: Resources 104
- Information Tab: Hardware 105
- Viewing Vital Signs 107
- Testing the Network 109
- Analyzing Cables in Windows 112
- Managing the LAN Device 114
- Viewing Driver Information 115
- Information Tab: Vital Signs 115
- Configuring the NDIS Driver 116
- Viewing Resource Information 122
- Configuring System Settings 123
- Viewing Statistics 123
- Viewing Licenses 128
- Configuring Teaming 129
- LiveLink 130
- Creating a Team 140
- Modifying a Team 142
- Adding a VLAN 143
- Deleting a VLAN 144
- Viewing BASP Statistics 145
- Troubleshooting BACS 146
- Performance Specifications 147
- Physical Characteristics 147
- Power Requirements 148
- Environmental Specifications 148
- FCC Class B Notice 149
- VCCI Class B Notice 149
- CE Notice 150
- Industry Canada, Class B 152
- Industry Canada, classe B 152
- B CLASS Device 153
- Back to Contents Page 154
- User Guide 155
- Diagnostic Test Descriptions 157
- Diagnostic Test Messages 159
- Hardware Diagnostics 161
- Troubleshooting Checklist 162
- Running a Cable Length Test 163
- Testing Network Connectivity 163
- RIPREP Utility Problem 165
- Broadcom Boot Agent 166
- Miscellaneous 167
- NetXtreme BCM57XX User Guide 168
- Step 1: Install OpenPegasus 169
- Enable Authentication 171
- Enable HTTP 171
- Enable HTTPS 171
- Uninstall 172
Produits connexes et manuels pour Matériel informatique Dell Broadcom NetXtreme Family of Adapters
(132 pages)
(24 pages)
KitchenAid KEMS378SSS02 manuels
Manuels d'utilisation et guides de l'utilisateur pour Cuisiniers KitchenAid KEMS378SSS02.
Nous fournissons des manuels en pdf 1 KitchenAid KEMS378SSS02 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels