Dell PowerVault DP100 Manuel d'utilisateur Page 71
- Page / 88
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2. Type your password and press <Enter>.
To disable the password security:
1. Turn on or reboot your system by pressing <Ctrl><Alt><Del>.
2. Type your password and press <Ctrl><Enter>.
When the Password Status option is set to Locked whenever you turn on your system or reboot your system by pressing <Ctrl><Alt><Del>, type your
password and press <Enter> at the prompt.
After you type the correct system password and press <Enter>, your system operates as usual.
If an incorrect system password is entered, the system displays a message and prompts you to re-enter your password. You have three attempts to enter the
correct password. After the third unsuccessful attempt, the system displays an error message showing the number of unsuccessful attempts and that the
system has halted and will shut down. This message can alert you to an unauthorized person attempting to use your system.
Even after you shut down and restart the system, the error message continues to be displayed until the correct password is entered.
Deleting or Changing an Existing System Password
1. When prompted, press <Ctrl><Enter> to disable the existing system password.
If you are asked to enter your setup password, contact your network administrator.
2. Enter the System Setup program by pressing <F2> during POST.
3. Select the System Security screen field to verify that the Password Status option is set to Unlocked.
4. When prompted, type the system password.
5. Confirm that Not Enabled is displayed for the System Password option.
If Not Enabled is displayed for the System Password option, the system password has been deleted. If Enabled is displayed for the System Password
option, press the <Alt><b> key combination to restart the system, and then repeat steps 2 through 5.
Using the Setup Password
Assigning a Setup Password
You can assign (or change) a setup password only when the Setup Password option is set to Not Enabled. To assign a setup password, highlight the Setup
Password option and press the <+> or <–> key. The system prompts you to enter and verify the password. If a character is illegal for password use, the
system beeps.
You can use up to 32 characters in your password.
As you press each character key (or the spacebar for a blank space), a placeholder appears in the field.
The password assignment is not case-sensitive. However, certain key combinations are not valid. If you enter one of these combinations, the system beeps.
To erase a character when entering your password, press <Backspace> or the left-arrow key.
After you verify the password, the Setup Password setting changes to Enabled. The next time you enter the System Setup program, the system prompts you
for the setup password.
A change to the Setup Password option becomes effective immediately (restarting the system is not required).
Operating With a Setup Password Enabled
If Setup Password is set to Enabled, you must enter the correct setup password before you can modify most of the System Setup options. When you start
the System Setup program, the program prompts you to enter a password.
If you do not enter the correct password in three attempts, the system lets you view, but not modify, the System Setup screens—with the following exception:
If System Password is not set to Enabled and is not locked through the Password Status option, you can assign a system password (however, you cannot
disable or change an existing system password).
NOTE: You can use the Password Status option in conjunction with the System Password and Setup Password options to further protect your system
from unauthorized changes.
NOTE: The setup password can be the same as the system password. If the two passwords are different, the setup password can be used as an
alternate system password. However, the system password cannot be used in place of the setup password.
- About Your System 2
- Connecting External Devices 4
- NIC Indicator Codes 4
- Hard-Drive Indicator Codes 6
- System Messages 7
- System Beep Codes 10
- Warning Messages 11
- Diagnostics Messages 11
- Alert Messages 11
- From the Utility Partition 12
- Glossary 14
- Getting Help 20
- Product Information 21
- Problems With Your Order 21
- Before You Call 22
- Contacting Dell 22
- Recommended Tools 33
- Inside the System 33
- Opening the System 34
- Front-Panel Drive Inserts 35
- Closing the System 36
- Connecting Drives 36
- Diskette Drive 37
- Optical or Tape Drives 38
- Hard Drives 40
- Cooling Shroud 46
- Cooling Fans 47
- Removing the Back System Fan 48
- Power Supply 49
- Replacing the Power Supply 50
- Expansion Cards 51
- Removing an Expansion Card 52
- Memory 53
- Installing Memory Modules 54
- Removing Memory Modules 54
- Microprocessor 55
- Installing a Processor 56
- Installing a RAC Card 57
- System Battery 58
- Removing the System Board 60
- Installing the System Board 61
- Jumpers and Connectors 63
- System Board Connectors 64
- System Setup Options 66
- CPU Information Screens 68
- Integrated Devices Screen 68
- Console Redirection Screen 69
- System Security Screen 69
- Exit Screen 69
- Using the System Password 70
- Using the Setup Password 71
- Start-Up Routine 74
- Checking the Equipment 74
- Problem 75
- Troubleshooting the Mouse 76
- Troubleshooting a NIC 77
- Troubleshooting a Fan 80
Produits connexes et manuels pour Matériel informatique Dell PowerVault DP100
(13 pages)
(74 pages)Lincoln Electric WELD-PAK 155 manuels
Manuels d'utilisation et guides de l'utilisateur pour Outils Lincoln Electric WELD-PAK 155.
Nous fournissons des manuels en pdf 1 Lincoln Electric WELD-PAK 155 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels