Dell PowerVault MD3200 Series Manuel du propriétaire Page 40
- Page / 74
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
40 Post Installation Tasks
Guidelines For Configuring Your Network For
iSCSI
This section provides general guidelines for setting up your network
environment and IP addresses for use with the iSCSI ports on your host server
and storage array. In order for hosts to communicate with management and/or
iSCSI ports of storage arrays, local NICs must be configured with IP addresses
capable of communication with the addresses listed in the IPv4/IPv6
worksheet. Your specific network environment may require different or
additional steps than shown here, so make sure you consult with your system
administrator before performing this setup.
Microsoft Windows Host Setup
To set up a Windows host network, you must configure the IP address and
netmask of each iSCSI port connected to the storage array. The specific steps
depend on whether you are using a Dynamic Host Configuration Protocol
(DHCP) server, static IP addressing, Domain Name System (DNS) server, or
Windows Internet Name Service (WINS) server.
NOTE: The server IP addresses must be configured for network communication to
the same IP subnet as the storage array management and iSCSI ports.
Using A DHCP server
1
In the
Control Panel
, select
Network connections
or
Network and
Sharing Center
and then click
Manage network connections
.
2
Right-click the network connection you want to configure and
select
Properties
.
3
On the
General
tab (for a local area connection) or the
Networking
tab
(for all other connections), select
Internet Protocol (TCP/IP)
, and then
click
Properties
.
4
Select
Obtain an IP address automatically
, then click
OK
.
Using static IP addressing
1
In the
Control Panel
, select
Network connections
or
Network and Sharing
Center
and then click
Manage network connections
.
book.book Page 40 Thursday, July 18, 2013 5:56 PM
- Deployment Guide 1
- Notes, Cautions, and Warnings 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- Introduction 7
- Support Matrix 8
- Introduction 9 9
- 10 Introduction 10
- Hardware Installation 11
- Connecting the Storage Array 12
- Cabling the Storage Array 12
- 14 Hardware Installation 14
- 16 Hardware Installation 16
- 18 Hardware Installation 18
- 20 Hardware Installation 20
- Enclosures 22
- Hardware Installation 25 25
- 26 Hardware Installation 26
- Software 27
- Console Installation 29
- Silent Installation 29
- Post Installation Tasks 31
- IPv4 Settings—Worksheet 33
- IPv6 Settings—Worksheet 34
- Post Installation Tasks 35 35
- Storage Array Configuration 37
- Post Installation Tasks 39 39
- Microsoft Windows Host Setup 40
- Using A DNS server 41
- Using A WINS Server 41
- Linux Host Setup 42
- Post Installation Tasks 43 43
- 44 Post Installation Tasks 44
- Uninstalling PowerVault MD 45
- Storage Software 45
- Getting Help 47
- Documentation Feedback 48
- Appendix—Load Balancing 49
- Least Queue Depth With Subset 50
- Management Options 51
- 52 Appendix—Load Balancing 52
- Management Only) 54
- Setting Up the Array 56
- Initiator 59
- Step 4: Configure Host Access 61
- What is CHAP? 62
- Target CHAP 62
- Mutual CHAP 62
- Storage Array (Optional) 63
- Host Server (Optional) 65
- <Username> 71
- <Password> 71
- <Authtype> 71
- 0i host ports 73
Produits connexes et manuels pour Réseaux de disques Dell PowerVault MD3200 Series
Réseaux de disques Dell H800 Spécifications
(23 pages)
(23 pages)
Electrolux Air-O-Convect AOS102GCD1 manuals
Owner’s manuals and user’s guides for Convection ovens Electrolux Air-O-Convect AOS102GCD1.
We providing 1 pdf manuals Electrolux Air-O-Convect AOS102GCD1 for download free by document types: User Manual
Commentaires sur ces manuels