Dell Latitude E6230 (Mid 2012) Manuel d'utilisateur

Dell Latitude E6230Owner's ManualRegulatory Model: P14TRegulatory Type: P14T001

10

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

Removing The ExpressCard1. Follow the procedures in Before Working Inside Your Computer.2. Press in on the ExpressCard to release it from the computer

3. Remove the battery from the computer.Installing the Battery1. Slide the battery into its slot until it clicks into place.2. Follow the procedures i

3. Loosen the captive screw that secures the base cover to the computer.4. Slide the base cover out of the computer.Installing the Base Cover1. Place

3. Disconnect and unroute the bluetooth cable.4. Remove the screw that secures the bluetooth module to the computer.5. Remove the bluetooth module.15

Installing the Bluetooth Module1. Connect the bluetooth cable to its connector.2. Tighten the screw to secure the bluetooth module to the computer.3.

5. Use a flat-headed screw driver to lift up the edge of the hard drive.6. Remove the hard drive.7. Remove the hard-drive connector from the hard driv

8. Remove the hard-drive caddy from the hard drive.Installing the Hard Drive1. Attach the hard-drive caddy to the hard drive.2. Connect the hard-drive

4. Lift and remove the memory module from its connector.5. Repeat steps 2 and 3 to remove the second memory module.Installing the Memory1. Insert the

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

4. Disconnect the Smart Card reader cable.5. Disconnect the touchpad cable.6. Remove the screws that secures the palmrest to the computer.20

7. Flip the base of the computer to a 45–degree angle.8. Press downward on the palmrest from the base of the computer.9. Remove the palmrest.21

Installing the Palmrest1. Align the palmrest to its slot.2. Press along the sides of the palmrest until it snaps in place.3. Flip the computer and tig

4. Flip the computer and remove the screws that secure the keyboard.5. Flip the keyboard over.6. Disconnect the keyboard data cable.23

7. Remove the keyboard.8. Peel off the mylar tape.9. Disconnect the keyboard cable.24

Installing the Keyboard1. Connect the keyboard cable.2. Affix the mylar tape to the keyboard.3. Connect the keyboard data cable.4. Slide the keyboard

4. Remove the screw that secures the WLAN card to the computer.5. Slide and remove the WLAN card out from its slot on the system board.Installing the

Removing the Heat-Sink Fan1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) SD Cardb) ExpressCardc) batteryd) base cove

5. Lift and remove the heat-sink fan.Installing the Heat-Sink Fan1. Replace the heat-sink fan in its slot.2. Tighten the screws that secure the heat-s

3. Loosen the screws that secure the heat-sink module to the computer.4. Remove the heat-sink module.Installing the Heat-Sink module1. Replace the hea

Contents1 Working on Your Computer... 7Before Work

Removing the Speakers1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) SD Cardb) ExpressCardc) batteryd) base cover3. D

5. Remove the screws that secure the speaker to the computer.6. Remove the screws that secure the other speaker to the computer.7. Remove the speakers

Installing the Speakers1. Align the speakers in the original position and connect the speaker cables.2. Tighten the screws to secure both the speakers

4. Disconnect the hall sensor cable.5. Remove the screws that secure the chassis base.6. Pull up the chassis base.33

Installing the Chassis Base1. Align the chassis base to the computer.2. Tighten the screws to secure the chassis base to the computer.3. Connect the f

4. Remove the screw that secures the hall sensor.5. Remove the hall sensor.Installing the Hall Sensor1. Replace the hall sensor in its slot.2. Tighten

Removing the Coin-Cell Battery1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) SD Cardb) ExpressCardc) batteryd) cover

3. Install the:a) base chassisb) speakersc) bluetooth moduled) heat-sink fane) keyboardf) palmrestg) base coverh) batteryi) ExpressCardj) SD card4. Fo

4. Disconnect the ExpressCard cage cable.5. Disconnect the power-connector cable.6. Remove the screws that secure the system board to the computer.38

7. Lift the left edge of the system board and raise it to a 45-degree angle.8. Remove the system board.Installing the System Board1. Place the system

Installing the Hall Sensor...

4. Install the:a) chassis baseb) display assemblyc) speakersd) heat-sink fane) heat sinkf) bluetooth moduleg) keyboardh) palmresti) base coverj) batte

4. Remove the power connector port.Installing the Power-Connector Port1. Insert the power-connector port in its slot.2. Connect the power connector to

3. Disconnect the ExpressCard reader cable.4. Remove the screws that secure the ExpressCard cage to the computer.5. Remove the ExpressCard cage.42

Installing the ExpressCard Cage1. Insert the ExpressCard cage into its compartment.2. Tighten the screws to secure the ExpressCard cage to the compute

4. Remove the screw that secures the WiFi-switch board to the computer.5. Remove the WiFi-switch board.Installing the WiFi-Switch Board1. Place the Wi

Removing the Smart Card Cage1. Follow the procedures in Before Working Inside Your Computer.2. Remove the:a) SD cardb) ExpressCardc) batteryd) base co

Installing the Smart Card Cage1. Place the smart card cage in its compartment.2. Tighten the screw that secures the smart card cage to the computer.3.

4. Work your way along to the sides and bottom edge of the display bezel.5. Remove the display bezel from the display assembly.Installing the Display

3. Remove the screws that secure the display panel to the display assembly.4. Flip the display panel over.5. Peel off the LVDS cable connector tape an

6. Remove the display panel from the display assembly.Installing the Display Panel1. Affix the LVDS cable connector tape and connect the LVDS cable to

7 Technical Specifications... 758 Contacting Del

3. Remove the screws from the bottom of the chassis4. Disconnect any antenna cables that may be connected to the wireless solutions and remove them fr

6. Remove the LVDS bracket.7. Disconnect the LVDS cable.8. Pull the antenna cables through the opening on top of the computer.51

9. Remove the screws that secure the display assembly to the computer.10. Pull up the display assembly from the chassis.Installing the Display Assembl

11. Follow the procedures in After Working Inside Your Computer.Removing the Camera1. Follow the procedures in Before Working Inside Your Computer.2.

5. Lift up the right edge of the camera.6. Flip the camera outwards.7. Disconnect the camera cable and remove the camera.Installing the Camera1. Insta

5. Install the:a) display bezelb) battery6. Follow the procedures in After Working Inside Your Computer.Removing the LVDS and Camera Cable1. Follow th

4. Peel back the adhesives that secures the LVDS and camera cable to the display assembly.5. Remove the LVDS and camera cable from the display assembl

3Additional InformationThis section provides information for the additional features that are part of your computer.Docking Port InformationThe dockin

58

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

6

Keys Navigation<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.Spacebar Expands or co

Option Description• Enabled• Enabled w/PXE (Default Setting)Parallel Port Allows you to define and set how the parallel port on the docking station op

Option Description• Enable SMART Reporting — This option is disabled by default.USB Configuration Allows you to define the USB configuration. The opti

Table 4. VideoOption DescriptionLCD Brightness Allows you to set the panel brightness when the ambient sensor is Off.Optimus Allows you to enable or d

Option DescriptionDefault Setting: Enable CPU XD SupportComputrace Allows you to activate or disable the optional Computrace software The options are

Option DescriptionHyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.Default Setting: EnabledTable 7. Power Mana

Option Description• Custom Charge — you can set the percentage to which the battery must charge.NOTE: All charging modes may not be available for all

Table 9. Virtualization SupportOption DescriptionVirtualization Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware

Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensur

NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to l

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

70

5DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

72

6Troubleshooting Your ComputerYou can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the op

Battery Status LightsIf the computer is connected to an electrical outlet, the battery light operates as follows:Alternately blinking amber light and

7Technical SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. F

AudioInternal high-definition audioExternal microphone-in/stereo headphones/external speakers connectorSpeakers twoInternal speaker amplifier 1 W (RMS

DisplayLatitude E6330 13.3"Dimensions:Latitude E6230Height 300.90 mm (11.84 inches)Width 180.00 mm (7.08 inches)Diagonal 317.30 mm (12.49 inches)

Battery• 6-cell (58 WHr) Lithium-ion batteryDimensions:3-cellDepth 29.97 mm (1.18 inches)Height 19.80 mm (0.78 inch)Width 208.00 mm (8.19 inches)6-cel

PhysicalLatitude E6230 Latitude E6330Height 22.40 mm to 24.70 mm (0.88 inch to 0.97 inch)25.40 mm to 30.10 mm (1 inch to 1.19 inches)Width 309.00 mm (

6. Close the display and turn the computer upside-down on a flat work surface.NOTE: To avoid damaging the system board, you must remove the main batte

80

8Contacting DellNOTE: If you do not have an active Internet connection, you can find contact information on your purchase invoice, packing slip, bill,

After Working Inside Your ComputerAfter you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turn