Dell Latitude E6430 (Mid 2012) Manuel d'utilisateur

Dell Latitude E6430 / E6430 ATGOwner's ManualRegulatory Model: P25GRegulatory Type: P25G001, P25G002

10

2Removing and Installing ComponentsThis section provides detailed information on how to remove or install the components from your computer.Recommende

Removing the ATG Port Covers1. Follow the procedures in Before Working Inside Your Computer.2. Remove the screws on the right ATG port cover.3. Remove

3. Slide the SD card out of the computer.Installing the Secure Digital (SD) Card1. Slide the SD card into its slot until it clicks into place.2. Follo

Removing the Battery1. Follow the procedures in Before Working Inside Your Computer.2. Slide the release latches to unlock the battery and flip the ba

Removing the Base Cover1. Follow the procedures in Before Working Inside Your Computer.2. Remove the screws that secure the base cover to the computer

3. Using a plastic scribe, pry under the keyboard trim to release it from the computer.4. Pry the keyboard trim along the sides and bottom.5. Lift up

3. Remove the screws that secure the keyboard to computer.4. Remove the screws that secure the keyboard to the palmrest assembly.5. Lift and turn the

7. Remove the keyboard from the computer.8. Peel back the adhesive tape securing the keyboard connector.9. Remove the keyboard cable from the keyboard

Removing the Hard Drive1. Follow the procedures in Before Working Inside Your Computer.2. Remove the battery.3. Remove the screws that secure the hard

Notes, Cautions, and WarningsNOTE: A NOTE indicates important information that helps you make better use of your computer.CAUTION: A CAUTION indicates

6. Remove the hard-drive caddy from the hard drive.7. Remove the hard-drive isolation from the hard drive.Installing the Hard Drive1. Install the hard

3. Press the optical-drive latch to release the optical drive from the computer.4. Pull the optical drive from the computer.5. Remove the screw that s

7. Remove the screws that secure the optical-drive latch bracket to the optical-drive assembly8. Remove the latch bracket from the optical drive.9. Re

Removing the Memory1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) base cover3. Pry the securing clips away fro

3. Disconnect the antenna cables from the WLAN card.4. Remove the screw that secures the WLAN card to the computer.5. Remove the WLAN card from its sl

Removing the Heat Sink1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) base cover3. Disconnect the heat-sink cab

4. Install:a) base coverb) battery5. Follow the procedures in After Working Inside Your Computer.Removing the Processor1. Follow the procedures in Bef

Removing the Bluetooth Card1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) hard drivec) base cover3. Remove the

6. Disconnect the cable from the bluetooth card.Installing the Bluetooth Card1. Connect the bluetooth cable to the bluetooth card.2. Place the bluetoo

4. Pry the coin-cell battery upward and remove it from the computer.Installing the Coin-Cell Battery1. Place the coin-cell battery in its slot.2. Conn

Contents1 Working on Your Computer... 7Before Work

4. Remove the ExpressCard cage from the computer.Installing the ExpressCard Cage1. Place the ExpressCard cage into its compartment.2. Tighten the scre

3. Disconnect the media board cable from the system board.4. Remove the screws that secure the media board to the computer.5. Remove the media board f

4. Install:a) palmrestb) display assemblyc) keyboardd) keyboard trime) bluetooth cardf) hard driveg) base coverh) battery5. Follow the procedures in A

5. Remove the power-connector bracket from the computer.6. Remove the power-connector cable from the computer.Installing the Power-Connector Port1. Co

3. Disconnect the power LED board cable.4. Remove the screw securing the power LED board to the display assembly.5. Remove the power LED board from th

4. Install:a) display panelb) display bezelc) display assemblyd) keyboarde) keyboard trimf) bluetooth moduleg) hard driveh) base coveri) battery5. Fol

5. Use the tab and pull the lower right edge of the modem card from the slot.6. Hold and remove the modem card from the computer.Installing the Modem

Removing the Modem Connector1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) base coverc) hard drived) bluetooth

5. Remove the screw that secures the modem-connector bracket to the computer.6. Remove the modem-connector bracket from the computer.7. Remove the mod

6. Install:a) system boardb) ExpressCard cagec) media board (available in E6430/E6430 ATG only)d) palmreste) display assemblyf) keyboardg) keyboard tr

Installing the Bluetooth Card...

4. Remove the I/O board from the computer.Installing the Input Output (I/O) Board1. Place the I/O board in its compartment.2. Tighten the screws to se

3. Remove the screws that secure the hard-drive support plate to the computer.4. Lift the hard-drive support plate from the computer.Installing the Ha

Removing the Palmrest1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) base coverc) hard drived) bluetooth carde)

6. Disconnect the touchpad cable from the system board.7. Disconnect the SD card cable from the system board.8. Lift and remove the palmrest from the

4. Install:a) keyboardb) keyboard trimc) bluetooth moduled) hard drivee) base coverf) battery5. Follow the procedures in After Working Inside Your Com

5. Remove the screw securing the LVDS cable bracket.6. Remove the LVDS cable bracket from the computer.7. Disconnect the LVDS cable from the back of t

9. Flip the system over and disconnect the media board cable from the system board.10. Remove the screws that secure the system board to the computer.

Installing the System Board1. Place the system board on the chassis.2. Tighten the screws to secure the system board to the computer.3. Connect the me

4. Remove the support bracket from the computer.5. Pull upwards on the tab to disconnect the LVDS cable from the computer.6. Disconnect the camera cab

8. Disconnect any antennas connected to wireless solutions.9. Remove any antennas from the routing channel.10. Remove the screws that secure the displ

4 System Setup... 63Boot Seq

Installing the Display Assembly1. Connect the display assembly to the computer.2. Flip the computer and tighten the screws to secure the display assem

5. Remove the display bezel from the display assembly.Installing the Display Bezel1. Place the display bezel onto the display assembly.2. Starting fro

4. Flip the display panel over.5. Peel off the LVDS cable connector tape and disconnect the LVDS cable from the display panel.6. Remove the display pa

Removing the Display-Hinge Caps1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) base coverc) hard drived) blueto

4. Install:a) display assemblyb) keyboardc) keyboard trimd) bluetooth carde) hard drivef) base coverg) battery5. Follow the procedures in After Workin

5. Remove the screws that secures the display hinges to the display assembly.6. Remove the display hinges from the display assembly.Installing the Dis

Removing the Camera1. Follow the procedures in Before Working Inside Your Computer.2. Remove:a) batteryb) display assemblyc) display bezeld) display p

3. Connect the LVDS and the camera cable to the camera.4. Install:a) display panelb) display bezelc) display assemblyd) battery5. Follow the procedure

5. Remove the LVDS and camera cable from the display assembly.Installing the LVDS and Camera Cable1. Route the LVDS and camera cable on the display as

3. Remove the screws that secure the speakers to the computer.4. Remove the speaker cable from the routing channel.5. Remove the speakers from the com

6

3. Install:a) system boardb) bluetooth cardc) ExpressCard caged) media board (available in E6430/E6430 ATG only)e) palmrestf) display assemblyg) keybo

3Docking Port InformationThe docking port is used for connecting the laptop to a docking station (optional).1. Docking Port61

62

4System SetupSystem Setup enables you to manage your computer hardware and specify BIOS‐level options. From the System Setup, you can:• Change the NVR

Keys Navigation<Enter> Allows you to select a value in the selected field (if applicable) or follow the link in the field.Spacebar Expands or co

Option Description• Enabled• Enabled w/PXE (Default Setting)Parallel Port Allows you to define and set how the parallel port on the docking station op

Option Description• Enable SMART Reporting — This option is disabled by default.USB Configuration Allows you to define the USB configuration. The opti

Table 4. VideoOption DescriptionLCD Brightness Allows you to set the panel brightness when the ambient sensor is Off.Optimus Allows you to enable or d

Option DescriptionDefault Setting: Enable CPU XD SupportComputrace Allows you to activate or disable the optional Computrace software The options are

Option DescriptionHyper-Thread Control Allows you to enable or disable the HyperThreading in the processor.Default Setting: EnabledTable 7. Power Mana

1Working on Your ComputerBefore Working Inside Your ComputerUse the following safety guidelines to help protect your computer from potential damage an

Option Description• Custom Charge — you can set the percentage to which the battery must charge.NOTE: All charging modes may not be available for all

Table 9. Virtualization SupportOption DescriptionVirtualization Specifies whether a Virtual Machine Monitor (VMM) can utilize the additional hardware

Updating the BIOS It is recommended to update your BIOS (system setup), on replacing the system board or if an update is available. For laptops, ensur

NOTE: If the password jumper is disabled, the existing System Password and Setup Password is deleted and you need not provide the system password to l

74

5DiagnosticsIf you experience a problem with your computer, run the ePSA diagnostics before contacting Dell for technical assistance. The purpose of r

76

6Troubleshooting Your ComputerYou can troubleshoot your computer using indicators like Diagnostic Lights, Beep Codes, and Error Messages during the op

Battery Status LightsIf the computer is connected to an electrical outlet, the battery light operates as follows:Alternately blinking amber light and

7Technical SpecificationsNOTE: Offerings may vary by region. The following specifications are only those required by law to ship with your computer. F

6. Close the display and turn the computer upside-down on a flat work surface.NOTE: To avoid damaging the system board, you must remove the main batte

Feature SpecificationNOTE: The computer supports up to the maximum of 16 GB memory; however, a 32-bit operating systems, such as the 32-bit version of

Table 21. Ports and ConnectorsFeatures SpecificationAudio one microphone/stereo headphone/speakers connectorVideo• one 15-pin VGA connector• 19-pin HD

Feature Specification• 1600 x 900 pixelsMaximum Brightness 200 nitsLatitude E6530:Height 210 mm (8.26 inches)Width 360 mm (14.17 inches)Diagonal 394.2

Table 24. KeyboardFeature SpecificationNumber of keys United States: 86 keys, United Kingdom: 87 keys, Brazil: 87 keys, and Japan: 90 keysNOTE: Numeri

Feature Specification6-cell / 9-cell 11.10 VDCTemperature range:Operating 0 °C to 35 °C (32 °F to 95 °F)Non-Operating –40 °C to 65 °C (–40 °F to 149 °

Feature SpecificationOperating 10 % to 90 % (non condensing)Storage 5 % to 95 % (non condensing)Altitude (maximum):Operating –15.24 m to 3048 m (–50 f

86

8Contacting Dell To contact Dell for sales, technical support, or customer service issues:1. Visit support.dell.com. 2. Verify your country or region

After Working Inside Your ComputerAfter you complete any replacement procedure, ensure you connect any external devices, cards, and cables before turn