Dell OpenManage Integration for VMware vCenter 2.0 Manuel d'utilisateur Page 144
- Page / 147
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
• Network connectivity: The server’s iDRAC must have network connectivity and must communicate with the
provisioning server over port 4433. You can obtain the IP address using a DHCP server or manually specify it in
the iDRAC Configuration Utility.
• Additional network settings: If using DHCP, enable the
Get DNS server address from DHCP
setting so that DNS
name resolution can occur.
• Provisioning service location: The iDRAC must know the IP address or host name of the provisioning service
server.
• Account access disabled: Enable the administrative account access to the iDRAC and if there are any iDRAC
accounts with administrator privileges, first disable them from within the iDRAC web console. Once Auto-
Discovery completes successfully, the administrative iDRAC account is re-enabled.
• Auto-Discovery enabled: The server’s iDRAC must have Auto-Discovery enabled so that the Auto-Discovery
process can begin.
Enabling or Disabling Administrative Accounts on iDRAC Servers
Before you can set up Auto-Discovery, disable all administrative accounts other than root. The root account is disabled
during the Auto-Discovery procedure. Once you have successfully set up Auto-Discovery, return to the Integrated Dell
Remote Access Controller 6 GUI and re-enable the accounts that were turned off. This procedure is for PowerEdge 11th
and 12th generation servers.
NOTE: To guard against a failed Auto-Discovery, you may want to enable a non-admin account on the iDRAC. This
allows remote access in the event the Auto-Discovery fails.
1. In a browser, type the iDRAC IP address.
2. Log in to the Integrated Dell Remote Access Controller GUI.
3. Do one of the following:
– For iDRAC6: In the left pane, select iDRAC Settings → Network/Security → Users tab.
– For iDRAC7: In the left pane, select iDRAC Settings → User Authentication → Users tab.
4. In the Users tab, locate any administrative accounts other than root.
5. To disable the account, under User ID, select the ID.
6. Click Next.
7. In the User Configuration page, under General, clear the Enable User check box.
8. Click Apply.
9. After you have successfully set up Auto-Discovery, to re-enable each account, repeat steps 1 to 8, but this time
select the
Enable User check box and click Apply.
Manually Configuring a PowerEdge 11th Generation Server for
Auto-Discovery
You must have the iDRAC and host IP addresses.
If you have not ordered your bare metal appliance to use Auto-Discovery from the factory, you can set it up manually.
iDRAC has two user interfaces, both are reached using the IP address of the iDRAC you want to set up.
On successful Auto-Discovery of bare-metal servers, the new administrator account is created or an existing account is
enabled with the credentials returned by the handshake service. All the other administrative accounts that were
disabled prior to Auto-Discovery will not be enabled. You must re-enable these administrator accounts after a
successful Auto-Discovery. See Enabling or Disabling Administrative Accounts on iDRAC.
144
- User's Guide Version 2.0 1
- Notes, Cautions, and Warnings 2
- Contents 3
- Introduction 9
- Inside the VMware vCenter 17
- Understanding Icon Buttons 17
- Locating the Software Version 18
- Refreshing the Screen Content 18
- Licensing Tab 18
- Opening Online Help 19
- Finding Help and Support 19
- Connection Profiles 21
- Editing a Connection Profile 23
- Deleting A Connection Profile 24
- Testing a Connection Profile 25
- Inventory History 27
- Running an Inventory Job Now 28
- Warranty History 29
- Running a Warranty Job Now 30
- Console Administration 31
- Virtual Appliance Management 33
- Setting Up The HTTP Proxy 34
- Setting Up the NTP Servers 35
- Setting up Global Alerts 36
- Managing Backup And Restore 36
- Scheduling Automatic Backups 37
- Configuring Network Settings 38
- Setting The Local Time Zone 39
- Rebooting Virtual Appliance 39
- Refreshing the Console View 40
- Read-only User Role 40
- About Logs 43
- Exporting Log Files 44
- Settings 45
- Installing the Dell 46
- About Firmware Updates 51
- User’s Guide 52
- Viewing Events 57
- Monitoring a Single Host 59
- Launching Management Consoles 61
- Buy License 63
- Single Host 67
- Renewing Host Warranty 88
- Datacenters or Clusters 97
- – NOT RECOVERABLE 100
- Datacenters and Clusters 101
- OpenManage 109
- Clusters 113
- Troubleshooting 119
- Table 4. Managed Nodes 124
- Clusters page? 125
- Mode Enabled? 126
- Bare Metal Deployment Issues 129
- Contacting Dell 130
- Virtualization—Related Events 131
- Data Integrity 137
- Dell Operation Role 139
- Understanding Privileges 141
- Understanding Auto-Discovery 143
- Auto-Discovery 144
- 15. Press ESC 147
Produits connexes et manuels pour Mise en réseau Dell OpenManage Integration for VMware vCenter 2.0
(194 pages)
(2 pages)KitchenAid KEMS378SSS02 manuels
Manuels d'utilisation et guides de l'utilisateur pour Cuisiniers KitchenAid KEMS378SSS02.
Nous fournissons des manuels en pdf 1 KitchenAid KEMS378SSS02 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels