Dell PowerVault TL4000 Instructions d'exploitation Page 21
- Page / 80
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Rackmounting the library
The library easily installs into a standard 19” rack system taking up 4U of space.
WARNING!
The AP Series tape library weighs 24.5 kg without media.
To reduce the risk of personal injury or damage to the library:
1) observe local health and safety requirements and guidelines for manual material handling,
2) obtain adequate assistance to lift and stabilize the library during installation or removal,
3) always remove all tapes to reduce the overall weight of the library.
Required tools:
1. #3 Phillips screwdriver
2. T10 Torx screwdriver (included in you shipment)
There are two sets of eight M6 screws in the accessory package that came with your library. The type of
rack that you have will determine the type of M6 screw that you will use.
To install the library:
3. Determine the location in you rack for your library to be installed and, using a pencil, mark the
location on each vertical rail in you rack.
4. Using the screws for your rack type, and a #3 Phillips screwdriver, secure one rail to each side
of the rack in your chosen rack location. Secure both the front and back of each rail to the
rack. The rails extend to fit a variety of rack depths. The correct orientation of the left and
right rails is shown in Figure 9.
Figure 9 Installing the rails into the rack
- Automatic Protection (AP) 1
- User and Service Guide 1
- Copyright 2
- Trademark Notices 2
- Contacting PivotStor, LLC 2
- About this guide 3
- 1 Warnings and symbols 4
- 1.1 Precautions 5
- 1.3 Rack stability 5
- 2 Contents 6
- 3 Figures 8
- 4 Tables 10
- 5.2 SCSI requirements 12
- 5.4 LUN scanning 12
- Back panel overview 16
- 5.6 Installing the library 18
- SCSI cable 19
- Rack mount kit: 19
- Documentation CD 19
- Library 19
- Terminator 19
- 6.1 Operating Modes 26
- 6.2 OCP Philosophy 26
- 6.3 Power-Up Display 26
- Idle Rand 27
- 6.4 Note about the LED’s 28
- 6.5 Input Modes 28
- 6.6 Power ON/OFF 29
- Robotic Drive 1 30
- AP Series 31
- PivotStor 31
- Commands 32
- Open Mailslot 32
- Service Menu 34
- Library Veryfy 34
- Run Test Service 34
- 6.8 Tape cartridges 35
- Tape’s media pool 36
- Data residing on the tape 36
- Age of the backup 36
- 1 Write-enabled 37
- 2 Write-protected 37
- 3 Write-protect switch 37
- Barcode label 37
- Insertion arrow 37
- 7.1 Overview 40
- 7.3 Library status icons 41
- 7.4 Login 41
- 7.5 Identity 42
- 7.6 Status 43
- 7.7 Configuration 44
- IP Address 45
- Network Mask 45
- Gateway Address 45
- Setting date/time 47
- Setting error log mode 47
- 7.8 Operations 48
- 7.9 Service 50
- 8.1 Possible tools needed 53
- 8.2 Electrostatic Discharge 53
- To remove a power supply: 56
- 9 Troubleshooting 60
- 9.2 Troubleshooting table 61
- 9.3 Service Procedures 64
- AP Series Remote Management 66
- Right magazine release 67
- Left magazine release 67
- Example error code 68
- 10 Technical specifications 74
- 11 Regulatory Information 76
- 12 Index 78
Produits connexes et manuels pour Mise en réseau Dell PowerVault TL4000
(11 pages)
(72 pages)Electrolux Air-O-Convect AOS102GCD1 manuals
Owner’s manuals and user’s guides for Convection ovens Electrolux Air-O-Convect AOS102GCD1.
We providing 1 pdf manuals Electrolux Air-O-Convect AOS102GCD1 for download free by document types: User Manual
Commentaires sur ces manuels