Dell PowerEdge 1850 Guide de dépannage Page 17
- Page / 73
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
not responding to system
requests.
Error: Incorrect memory configuration.
Ensure memory in slots DIMM1_A and
DIMM1_B, DIMM2_A and DIMM2_B, DIMM3_A
and DIMM3_B match identically in size,
speed, and rank.
One or more unmatched pairs
of memory modules are
detected
Ensure that the memory modules are installed in matched pairs. See "General
Memory Module Installation Guidelines" in "Installing System Components."
Error: Incorrect memory configuration.
Memory slots DIMM3_A and DIMM3_B only
support single rank DIMMs. Remove the
dual rank DIMMs from slots DIMM3_A and
DIMM3_B.
Dual rank memory modules
are installed in slots DIMM3_A
and DIMM3_B.
Ensure that only single rank memory modules are installed in slots DIM3_A and
DIMM3_B. See "General Memory Module Installation Guidelines" in "Installing
System Components."
Error: Incorrect memory configuration.
Move DIMM3_A and DIMM3_B into DIMM2_A
and DIMM2_B.
Memory modules are not
installed in consecutive banks.
Move memory modules from slots DIMM3_A and DIMM3_B into DIMM2_A and
DIMM2_B. See "General Memory Module Installation Guidelines" in "Installing
System Components."
Error: Incorrect memory configuration.
Swap the DIMMs in slots DIMM1_A and
DIMM1_B with DIMMs in slots DIMM2_A
and DIMM2_B.
If dual-rank memory modules
are installed in the system,
they must be installed in slots
DIMM1_A and DIMM1_B.
Swap memory modules in slots DIMM2_A and DIMM2_B with modules in
DIMM1_A and DIMM1_B. See "General Memory Module Installation Guidelines" in
"Installing System Components."
Error: Incorrect memory configuration.
Memory slots DIMM3_A and DIMM3_B must
be empty if dual rank memory DIMMS are
in slots DIMM2_A and DIMM2_B.
Memory modules are installed
in bank3. Dual rank memory
modules are installed in banks
1 and 2.
Remove memory modules from slots DIMM3_A and DIMM3_B. See "General
Memory Module Installation Guidelines" in "Installing System Components."
Error: More than one RAC detected,
system halted.
Two RACs are installed, or
faulty or improperly installed
RAC.
Ensure that only one RAC is installed. Ensure that the RAC is properly installed.
See "Troubleshooting Expansion Cards" in "Troubleshooting Your System," or
"Installing a RAC Card" in "Installing System Options."
Error: Remote Access Card
initialization failure.
Faulty or improperly installed
RAC.
Ensure that the RAC is properly installed. See "Troubleshooting Expansion
Cards" in "Troubleshooting Your System," or "Installing a RAC Card" in
"Installing System Options."
Error 8602: Auxiliary device failure.
Verify that the keyboard and mouse are
securely attached to correct
connectors.
Loose or improperly
connected mouse or keyboard
cable; faulty mouse or
keyboard.
Replace the mouse. If the problem persists, replace the keyboard.
Gate A20 failure
Faulty keyboard controller
(faulty system board).
See "Getting Help."
General failure
Operating system corrupted
or improperly installed.
Reinstall the operating system.
Keyboard controller failure
Faulty keyboard controller
(faulty system board).
See "Getting Help"
Keyboard data line failure
Keyboard failure
Keyboard stuck key failure
Loose or improperly
connected keyboard cable;
faulty keyboard; faulty
keyboard controller.
Ensure that the keyboard is properly connected. If the problem persists, replace
the keyboard. If the problem persists, see "Getting Help."
Keyboard fuse has failed.
Keyboard fuse has failed.
Replace the keyboard.
Faulty system board. See "Getting Help."
Manufacturing mode detected
System is incorrectly
configured.
After the message appears during system boot, press <Alt><F> to turn off
manufacturing mode.
Memory address line failure at
address, read value expecting value
Memory double word logic failure at
address, read value expecting value
Memory odd/even logic failure at start
address to end address
Memory write/read failure at address,
read value expecting value
Faulty or improperly installed
memory modules, or faulty
system board.
Ensure that all memory modules are properly installed. See "Troubleshooting
System Memory" in "Troubleshooting Your System." If the problem persists, see
"Getting Help."
Memory mirroring enabled
Memory mirroring enabled
You can enable memory mirroring using the System Setup program if the
memory is configured to support mirroring. For more information, see "General
Memory Module Installation Guidelines" in "Installing System Components," and
Using the System Setup Program" in your User's Guide.
Memory tests terminated by keystroke
The spacebar was pressed
during POST to terminate the
memory test.
Information only.
No boot device available
Faulty or missing diskette
drive, optical drive, or hard
drive.
Check the Integrated Devices configuration settings in the System Setup
program. See "Using the System Setup Program" in your User's Guide. Ensure
that either SCSI Controller, Diskette Controller, or IDE CD-ROM Controller is
enabled. If the system is booting from a SCSI controller, ensure that the
controller is properly connected. If the problem persists, replace the drive. See
"Installing Drives."
No boot sector on hard-disk drive
An operating system is not on
the hard drive.
Check the hard drive configuration settings in the System Setup program. See
"Using the System Setup Program" in your User's Guide.
No timer tick interrupt
Faulty system board.
See "Getting Help."
Not a boot diskette
Not a bootable diskette.
Use a bootable diskette.
PCI BIOS failed to install
Loose cables to expansion
card(s); faulty or improperly
installed expansion card.
Ensure that all appropriate cables are securely connected to the expansion
cards. See "Troubleshooting Expansion Cards," in "Troubleshooting Your
System."
- Notes, Notices, and Cautions 1
- Abbreviations and Acronyms 1
- System Board Jumpers 2
- System Board Connectors 3
- Riser Board Connectors 4
- SCSI Backplane Connectors 5
- I/O Connectors 7
- Video Connector 8
- USB Connectors 9
- Integrated NIC Connectors 9
- Network Cable Requirements 10
- Introduction 11
- System Status Indicators 12
- Power Indicator Codes 15
- NIC Indicator Codes 15
- System Messages 16
- System Beep Codes 18
- Warning Messages 19
- Diagnostics Messages 20
- Alert Messages 20
- Before You Begin 21
- From the Utility Partition 23
- Back to Contents Page 25
- Start-Up Routine 26
- Checking the Equipment 27
- Troubleshooting a NIC 29
- Inside the System 30
- Opening the System 30
- Closing the System 31
- Problem 32
- System Board Components 43
- System Battery 44
- Power Supplies 45
- Expansion Cards 46
- Riser Card 47
- Removing the Riser Card 48
- Installing the Riser Card 48
- System Memory 49
- Installing Memory Modules 50
- Processor 51
- Installing a RAC Card 53
- Installing Drives 55
- Removing a SCSI Hard Drive 56
- Configuring the Boot Drive 59
- Connecting the Card 61
- Getting Help 62
- Problems With Your Order 63
- Product Information 63
- Before You Call 64
- Contacting Dell 64
- Abbreviations and Acronyms 73
Produits connexes et manuels pour Serveurs Dell PowerEdge 1850
Serveurs Dell T110 Guide de démarrage rapide
(50 pages)
(50 pages)
Serveurs Dell 56192370 Fiche technique
(1 pages)
(1 pages)
Serveurs Dell 57095286 Fiche technique
(1 pages)
(1 pages)
Serveurs Dell 56193617 Fiche technique
(1 pages)
(1 pages)
Serveurs Dell 56192483 Fiche technique
(1 pages)
(1 pages)
Serveurs Dell 57099896 Fiche technique
(1 pages)
Serveurs Dell 10511100 Fiche technique
(1 pages)
(1 pages)
KitchenAid KEMS378SSS02 manuels
Manuels d'utilisation et guides de l'utilisateur pour Cuisiniers KitchenAid KEMS378SSS02.
Nous fournissons des manuels en pdf 1 KitchenAid KEMS378SSS02 à télécharger gratuitement par type de document : Manuel de l'utilisateur
Commentaires sur ces manuels