Dell OpenManage Server Administrator Version 7.3 Manuel d'utilisateur Page 89
- Page / 190
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
name=value pair 1
config=
name=value pair 2 Description
teamednic1nic2: Enables NIC teaming functionality.
dracnic: Enables DRAC NIC if DRAC 5 is installed.
NOTE: The nicselection option is supported only
on PowerEdge 9G to 11G systems. From
PowerEdge 12G systems onwards, primarynw
and failovernw replaces nicselection.
primarynw=dedicated | lom1 | lom2 |
lom3 | lom4
dedicated: Configures dedicated port as primary
network for remote access.
NOTE: This option requires license to configure
primarynw as dedicated. If the appropriate
license is not installed or has expired, the system
displays an error message. For more information,
see
Dell License Manager
at dell.com/
openmanagemanuals.
lom 1: Configures lom1 port as the primary network for
remote access.
lom 2: Configures lom2 port as the primary network for
remote access.
lom 3: Configures lom3 port as the primary network for
remote access.
lom 4: Configures lom4 port as the primary network for
remote access.
NOTE: The primarynw option is supported from
PowerEdge12G systems onward. If the
primarynw is set to dedicated, then set
failovernw to none.
failovernw=none | lom1 | lom2 | lom3 |
lom4 | all
none: Configures the failover network to none.
lom 1:Configures the failover network to lom 1.
lom 2: Configures the failover network to lom 2.
lom 3: Configures the failover network to lom 3.
lom 4: Configures the failover network to lom 4.
all: Configures the failover network to all loms.
NOTE: The failovernw option is supported on
PowerEdge12G systems onward. Configure both
primarynw and failovernw to set the nicselection.
The primarynw and failovernw options cannot
have the same value.
NOTE: Failovernw requires license to configure
the ports. If the appropriate license is not
installed or has expired, the system displays an
error message. For more information, see
Dell
License Manager
at dell.com/
openmanagemanuals.
ipaddress=IP
Sets the IP address if you have selected static as the
IP address source for the BMC LAN interface.
subnet=Subnet Sets a subnet mask if you have selected static as the
IP address source for the BMC LAN interface.
89
- Notes, Cautions, and Warnings 2
- Contents 3
- Introduction 11
- Primary CLI Commands 12
- Success Messages 13
- Failure Messages 13
- Command Syntax Overview 14
- Using The omhelp Command 17
- Table 2. Optional Parameters 18
- Instrumentation Service 19
- Omreport Chassis Intrusion 32
- Dell License Manager Guide 39
- Omreport Licenses 44
- Commands 44
- Commands For Viewing Logs 45
- Pedestinations 49
- Remote Access 54
- Information 54
- Processor 54
- Memory Array 55
- Firmware 55
- Omreport Preferences Commands 56
- Omreport Preferences Messages 57
- Omconfig About 63
- Dell License 85
- Default Warning Thresholds 87
- License Manager 88
- Dell License Manager 89
- IPv6 address 90
- Usage Of Dracusergroup=custom 94
- Omconfig Preferences 97
- Omconfig Preferences Snmp 98
- Defining Alert Actions 100
- Available Alert Actions 101
- Commands For Clearing Logs 103
- Severity 108
- Example Recovery Commands 109
- Example Shutdown Commands 110
- Adding Lease Information 116
- Adding Outsource Information 118
- Adding Owner Information 119
- Adding Support Information 121
- Adding System Information 122
- Adding Warranty Information 122
- CLI Command Syntax 125
- Syntax Of Command Elements 126
- Omreport Storage Commands 129
- Omreport Physical Disk Status 130
- Omreport Controller Status 131
- Omreport Enclosure Status 131
- Omreport Fan Status 132
- Omreport Power Supply Status 133
- Omreport EMM Status 133
- Omreport Battery Status 134
- Omreport Global Information 135
- Omreport Connector Status 135
- Omreport Cachecade Status 136
- Omreport PCIe SSD Status 136
- Omreport Fluid Cache Status 136
- Omreport Storage Tape 137
- Omconfig Storage Commands 139
- Omconfig Blink Physical Disk 140
- Omconfig Online Physical Disk 143
- Dell OpenManage Online Help 144
- Omconfig Clear Physical Disk 145
- Omconfig Check Consistency 149
- Omconfig Blink Virtual Disk 150
- Omconfig Unblink Virtual Disk 151
- Omconfig Delete Virtual Disk 153
- Omconfig Format Virtual Disk 154
- Omconfig Secure Virtual Disk 154
- Omconfig Rename Virtual Disk 156
- Omconfig Controller Commands 157
- Omconfig Rescan Controller 159
- Dell OpenManage 160
- Online Help 160
- Controller=id 164
- Cachepolicy=<d 165
- Omconfig Set Reconstruct Rate 169
- Omconfig Set Patrol Read Mode 171
- Omconfig Start Patrol Read 171
- Omconfig Stop Patrol Read 171
- Omconfig Create Cachecade 172
- Omconfig Rekey LKM Controller 172
- Omconfig Enclosure Commands 173
- Omconfig Battery Commands 176
- Omconfig Global Commands 177
- Omconfig Connector Commands 179
- Omconfig Cachecade Commands 180
- Omconfig PCIe SSD Commands 181
- Omconfig Fluid Cache Commands 183
- Omconfig Partition Command 183
- List (lst) 188
- Table (tbl) 189
- Custom Delimited Format (cdv) 189
Produits connexes et manuels pour Serveurs Dell OpenManage Server Administrator Version 7.3
(52 pages)
Serveurs Dell 58260075 Fiche technique
(1 pages)
(1 pages)
Serveurs Dell 58259908 Fiche technique
(1 pages)
(1 pages)
Grandview GPCK-MA manuály
Uživatelské manuály a uživatelské příručky pro Projektory Grandview GPCK-MA.
Poskytujeme 1 manuály pdf Grandview GPCK-MA ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Commentaires sur ces manuels