Dell PowerEdge C6100 Manuel du propriétaire Page 49
- Page / 160
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Using the System Setup Program 49
NOTE: When Flow Control is set to Software, the Hyper Terminal on remote side is
discontinued by pressing <Ctrl><S>. But the <Ctrl><S> is also the Setup Key Stroke
for setting onboard NIC PXE Option ROM Configuration. Therefore, we suggest
users change <Ctrl><S> to <Ctrl><B> in PXE OPROM Configuration in order to avoid
that the Hyper Terminal on remote side is discontinued when pressing <Ctrl><S>.
IPMI Configuration
Redirection After BIOS POST
(Always default)
Selects the settings for the redirection. This item
disappears when Remote Access is disabled:
•
Disabled
: turns off the redirection after POST.
•
Boot Loader
: redirection is active during POST and
boot loader.
•
Always
: redirection is always active. (Some
operating systems may not work if set to
Always
)
Terminal Type
(VT100 default)
Selects the target terminal type. This item disappears
when Remote Access is disabled.
VT-UTF8 Combo Key
Support (Enabled default)
Enables or disables VT-UTF8 combination key
support for ANSI/VT100 terminals. This item
disappears when Remote Access is disabled.
Terminal Display Mode
(Normal mode default)
Selects Terminal Display Mode.
Options:
• Normal Mode
• Recorder Mode
Option Description
Status Of BMC Displays BMC status.
BMC Firmware Revision Displays BMC Firmware Revision.
View BMC System
Event Log
Selecting this option and pressing Enter, displays:
Total Number Of Entries, SEL Entry Number,
SEL Record ID, SEL Record Type,
Event Time Stamp, Generator ID, Event Message
Format Version, Event Sensor Type, Event Sensor
Number, Event Dir Type, and Event Data.
Option Description
book.book Page 49 Thursday, March 4, 2010 4:38 PM
- Hardware Owner’s 1
- Notes, Cautions, and Warnings 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 8 Contents 8
- 10 Contents 10
- About Your System 11
- 12 About Your System 12
- 14 About Your System 14
- Hard-Drive Indicator Patterns 15
- 16 About Your System 16
- NIC Indicator Codes 18
- (KVM Over IP Port) 19
- Power Supply Indicator Codes 21
- BMC Heart Beat LED 22
- POST Error Codes 23
- 24 About Your System 24
- 26 About Your System 26
- 28 About Your System 28
- 30 About Your System 30
- 32 About Your System 32
- 34 About Your System 34
- Start Menu 35
- System Setup Options at Boot 36
- Console Redirection 36
- Main Menu 37
- AMIBIOS Settings 38
- Processor Settings 38
- System Memory Settings 38
- CPU Configuration 39
- Memory Configuration 40
- IDE Configuration 41
- Primary IDE Master 41
- USB Configuration 43
- PCI Configuration 44
- Boot Settings Configuration 45
- Server Menu 47
- System Management 48
- Remote Access Configuration 48
- IPMI Configuration 49
- LAN Configuration 50
- IP Address 50
- Subnet Mask 51
- Default Gateway IP 51
- Inside the System 54
- Removing a Hard-Drive Blank 55
- Removing a Hard-Drive Carrier 56
- Removing a Power Supply 59
- Installing a Power Supply 60
- System-Board Assembly 61
- Removing the Cooling Shroud 63
- Installing the Cooling Shroud 64
- Removing the Heat Sink 64
- 1 screw (4) 2 heat sink 65
- Installing the Heat Sink 66
- Removing a Processor 66
- Installing a Processor 68
- Removing the Expansion Card 69
- Expansion-Card Connector 72
- 3 expansion-card bracket 73
- Mezzanine Card 74
- Supported DIMM Configuration 77
- Removing Memory Modules 79
- Installing Memory Modules 80
- Interposer Extenders 82
- Replacing the System Battery 84
- Removing the RAID Battery 85
- Installing the RAID Battery 86
- Removing a System Board 89
- Installing a System Board 90
- Opening the System 91
- Closing the System 92
- Removing a Cooling Fan 92
- Installing a Cooling Fan 94
- Fan Controller Board 97
- Removing the Midplanes 99
- 1 screw (9) 2 upper midplane 101
- Installing System Components 102
- Installing the Midplanes 104
- Removing the Backplane 105
- Installing the Backplane 108
- Removing the Front Panel 109
- Installing Front Panel 111
- Troubleshooting Your System 113
- Troubleshooting a USB Device 114
- Troubleshooting a NIC 116
- Troubleshooting a Wet System 117
- Troubleshooting a Fan 120
- Troubleshooting System Memory 121
- Troubleshooting a Hard Drive 123
- Troubleshooting Processors 126
- IRQ Assignment Conflicts 127
- Jumpers and Connectors 129
- 3.5" drives 130
- 2.5" drives 132
- Midplane Connectors 134
- Mezzanine Card Connectors 136
- 138 Jumpers and Connectors 138
- Jumper Settings 139
- 140 Jumpers and Connectors 140
- Backplane Jumper Settings 141
- 142 Jumpers and Connectors 142
- Getting Help 143
- 144 Getting Help 144
- Glossary 145
- 146 Glossary 146
- 148 Glossary 148
- 150 Glossary 150
- 152 Glossary 152
- 154 Glossary 154
- Index 155 155
- Index 157 157
- Index 159 159
- 160 Index 160
Produits connexes et manuels pour Serveurs Dell PowerEdge C6100
Serveurs Dell DR4100 Manuel d'utilisateur
(119 pages)
(119 pages)
Serveurs Dell R2 Manuel d'utilisateur
(34 pages)
(34 pages)
Serveurs Dell PowerEdge R720 Livre blanc
(17 pages)
(17 pages)
(54 pages)
Serveurs Dell R2 Manuel d'utilisateur
(32 pages)
(32 pages)
Serveurs Dell PowerEdge R420 Livre blanc
(25 pages)
(25 pages)
Serveurs Dell R805 Manuel d'utilisateur
(84 pages)
(84 pages)
© 2020, manymanuals.fr. Tous droits réservés | 1.991 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels