Dell PowerEdge 1750 Guide de dépannage télécharger pdf (Page 25)

initialization failure

RAC. If the problem persists, you may need to replace the

system board. See "Getting Help."

Gate A20 failure

Faulty keyboard controller (defective

system board).

Replace the system board. See "Getting Help."

General failure

Application program or operating system

failure.

Reboot. If the message reappears, see your software

documentation.

Hard disk controller failure

Hard disk read failure

Incorrect configuration settings in the

System Setup program, improperly

connected hard drive, or faulty hard-

drive controller subsystem (defective

system board).

Check the hard-drive configuration settings in the System

Setup program. See "Using the System Setup Program" in the

User's Guide. Reinstall the hard drive. See "Installing SCSI

Hard Drives" in "Installing Drives."

Invalid configuration information - please

run SETUP program.

Incorrect configuration settings in the

System Setup program, the NVRAM_CLR

jumper is installed, or the system

battery is faulty.

Check the System Setup configuration settings. See "Using

the System Setup Program" in the User's Guide. Remove the

NVRAM_CLR jumper. See FigureA-2 for jumper location.

Replace the battery. See "Replacing the System Battery" in

"Installing System Options."

Invalid memory configuration detected.

Potential for data corruption exists!

Memory modules are not installed in

matched pairs.

Install memory modules in matched pairs. See "Installing

Memory Modules" in "Installing System Options."

Invalid NVRAM configuration, resource re-

allocated

System configuration data has been

ignored.

Check the System Setup configuration settings. See "Using

the System Setup Program" in the User's Guide.

I/O card parity interrupt at address

Expansion card(s) is improperly installed

or faulty.

Reinstall the expansion card(s). See "Installing Expansion

Cards" in "Installing System Options." If the problem persists,

replace the expansion card(s).

Keyboard controller failure

Defective keyboard/mouse controller

(defective system board).

Replace the system board. See "Getting Help."

Keyboard data line failure

Keyboard stuck key failure

Keyboard clock line failure

Keyboard failure

Keyboard cable connector is loose or

improperly connected; defective

keyboard; defective keyboard/mouse

controller (defective system board).

Check the keyboard cable connection. Replace the keyboard.

If the problem persists, replace the system board. See

"Getting Help."

Memory allocation error

Memory module(s) is not connected

properly, or an application program or

the operating system failed.

Reseat the modules. See "Installing Memory Modules" in

"Installing System Options." Reboot the system. If the

message reappears, see your software documentation.

Memory address line failure at address, read

value expecting value

Memory high data line failure at start

address to end address

Memory high address line failure at start

address to end address

Memory double word logic failure at start

address to end address

Memory double word logic failure at address,

read value expecting value

Memory odd/even logic failure at start

address to end address

Memory odd/even logic failure at address,

read value expecting value

Memory write/read failure at address, read

value expecting value

Memory write/read failure at start address

end address

Faulty or improperly seated memory

modules or defective system board.



Remove and reseat the memory modules. See "Installing

Memory Modules" in "Installing System Options." If the

problem persists, replace the memory modules. If the problem

persists, see "Getting Help."

Memory parity failure at start address to end

address

Memory parity error at address

Improperly seated or faulty memory

modules.

Remove and reseat the memory modules. See "Installing

Memory Modules" in "Installing System Options." If the

problem persists, replace the memory modules. If the problem

persists, see "Getting Help."

No boot device available

Faulty diskette, diskette/CD drive

subsystem, hard drive, or hard-drive

subsystem; no boot disk in drive A.

Replace the diskette or the hard drive. See "Installing Drives."

If the problem persists, replace the system board. See

"Getting Help."

No boot sector on hard- disk

No operating system on the hard drive.

Check the hard-drive configuration settings in the System

Setup program. See "Using the System Setup Program" in the

User's Guide.

No timer tick interrupt

Defective system board.

Replace the system board. See "Getting Help."

No PXE-capable device available

<F12> was pressed during POST and no

PXE devices are detected.

Check the cables connected to the NICs. Check the

configuration settings in the System Setup program for the

NICs. See "Using the System Setup Program" in the User's

Guide.

Non-system disk or disk error

Faulty diskette, diskette drive

subsystem, or hard-drive subsystem.

Replace the diskette. Reseat all drives and reboot the

system. If the error message reappears, see "Getting Help."

Not a boot diskette

No operating system on diskette.

Use a bootable diskette.

1 2 ... 20 21 22 23 24 25 26 27 28 29 30 ... 73 74

Commentaires sur ces manuels

Pas de commentaire

Dell PowerEdge 1750 Guide de dépannage Page 25

Commentaires sur ces manuels

Produits connexes et manuels pour Serveurs Dell PowerEdge 1750