Dell PowerEdge 1750 Guide de dépannage télécharger pdf (Page 26)

PCI BIOS failed to install

PCI device (option ROM) checksum

failure is detected during shadowing.

Contact the PCI device manufacturer to obtain a suitable

replacement PCI option ROM. Follow the manufacturer's

instructions to install the option ROM.

Plug & Play Configuration Error

Error encountered when initializing the

PCI device, or the system board is

defective.

Install the NVRAM_CLR jumper and reboot the system. If the

problem persists, replace the system board. See "Getting

Help."

Plug & Play Configuration Error PCI_n

Error encountered when initializing the

PCI adapter.

Install the NVRAM_CLR jumper and reboot the system. If the

problem persists, replace the specified expansion-card. See

"Installing Expansion Cards" in "Installing System Options." If

the problem persists, replace the system board. See "Getting

Help."

Primary backplane error

Improperly attached or missing

backplane.

Ensure that the SCSI backplane board is fully seated. See

"Troubleshooting SCSI Hard Drives" in "Troubleshooting Your

System."

Primary IDE device 0 not found

Primary IDE device 1 not found

Improperly connected or missing IDE

device.

Ensure that the device's interface cable is securely connected

to the SCSI backplane board. Replace the device. If the

problem persists, see "Getting Help."

Processor 1 internal error

Processor 2 internal error

Defective microprocessor or system

board (reported by the NMI handler).



Replace the specified microprocessor. See "Installing

Microprocessors" in "Installing System Options." If the

problem persists, replace the system board. See "Getting

Help."

Processor bus error

PCI bus error

IMB bus error

Defective system board (reported by the

NMI handler).

Replace the system board. See "Getting Help."

Processor x is not a 533-MHz system bus

processor

This system bus speed is not supported on

this system board.

This system supports only Intel®

Xeon™533-MHz front-side-bus (system

bus) processors.

Reboot the system. If you receive beep code 4-4-3 (processor

frequency mismatch), replace processor x with a supported

processor. See "Installing Microprocessors" in "Installing

System Options."

If a beep code does not occur at system boot, turn off the

system, install the NVRAM_CLR jumper, and reboot the

system. If the message reappears, see "Getting Help."

Read fault

Requested sector not found

Faulty diskette, diskette-drive

subsystem, or hard-drive subsystem.

Replace the diskette, or reseat all drives and reboot the

system. If the message reappears, see "Getting Help."

Reset failed

Improperly connected diskette/tape

drive, hard drive, or power cable.

Check the drive and cable connections, and reset the system

again. If the message reappears, see "Getting Help."

ROM bad checksum = address

Expansion card improperly installed or

faulty.

Reinstall the expansion card. See "Installing Expansion

Cards" in "Installing System Options."

Sector not found

Seek error

Seek operation failed

Defective sectors on diskette or hard

drive.

Faulty diskette, diskette-drive

subsystem, or hard-drive subsystem.

Replace the diskette, or reseat all drives and reboot the

system. If the message reappears, see "Getting Help."

Shutdown failure

Defective system board.

Replace the system board. See "Getting Help."

System backplane error

Improperly attached or missing SCSI

backplane.

Check that the SCSI backplane board is fully seated. See

"Troubleshooting SCSI Hard Drives" in "Troubleshooting Your

System."

System halted! Must power down.

Wrong password entered too many

times.

Reboot the system and enter the correct password. If the

problem persists, see "Disabling a Forgotten Password" in

"Jumpers and Connectors."

System parity error

Defective expansion card(s) or

improperly seated or faulty memory

modules (reported by the NMI handler).

Replace the expansion cards one at a time until the error is

corrected. See "Installing Expansion Cards" in "Installing

System Options."

Remove and reseat the memory modules. See "Installing

Memory Modules" in "Installing System Options." If the

problem persists, replace the memory modules. If the problem

persists, see "Getting Help."

The following memory DIMMs are unsupported:

DIMM_xx.

This system only supports 266 MHz DIMMs.

One or more of the installed DIMMs has

a frequency less than 266 MHz. System

memorymustberatedfor266MHz.

Replace lower-speed DIMM(s) with modules rated for 266-

MHz operation. See "Installing Memory Modules" in "Installing

System Options."

Time-of-day clock stopped

Defective battery or faulty chip

(defective system board).

Replace the system battery. See "Replacing the System

Battery" in "Installing System Options." If the problem

persists, replace the system board. See "Getting Help."

Time-of-day not set - please run SETUP

program

Incorrect Time or Date settings or

defective system battery.

Check the Time and Date settings. See "Using the System

Setup Program" in the User's Guide. If the problem persists,

replace the system battery. See "Replacing the System

Battery" in "Installing System Options." If the problem

persists, replace the system board. See "Getting Help."

Timer chip counter 2 failed

Defective system board.

Replace the system board. See "Getting Help."

Unsupported CPU combination

Microprocessor combination is not

supported by the system.

Install a supported microprocessor combination. See

"Installing Microprocessors" in "Installing System Options."

Unsupported CPU stepping detected.

Microprocessor is not supported by the

system.

Install the correct version of the microprocessor in the

specified microprocessor socket. See "Installing

Microprocessors" in "Installing System Options."

Utility partition not available

<F10> key was pressed during POST,

Create a utility partition on the boot hard drive. See "Using

1 2 ... 21 22 23 24 25 26 27 28 29 30 31 ... 73 74

Commentaires sur ces manuels

Pas de commentaire

Dell PowerEdge 1750 Guide de dépannage Page 26

Commentaires sur ces manuels

Produits connexes et manuels pour Serveurs Dell PowerEdge 1750