Dell Lifecycle Controller 2 Version 1.3.0 Manuel de service Page 153
- Page / 240
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
<n1:PossibleValues>NONE</n1:PossibleValues>
<n1:PossibleValues>PXE</n1:PossibleValues>
<n1:PossibleValues>NONE</n1:PossibleValues>
</n1:DCIM_NICEnumeration>
15.10 Setting the
IscsiOffloadMode
Attribute
The SetAttribute() method is used to set or change the value of a CNA attribute. Enable the
NICMode,
IscsiOffloadMode
, and
FcoeOffloadMode
personality attributes to enable the
corresponding
personalities: NIC, ISCSI, and FCOE.
For Broadcom CNA cards, the partitions on each port can be set to any personality. NICMode can
always be enabled or disabled for any of the given partitions. For the
IscsiOffloadMode
and
FcoeOffloadMode
personalities, up to two personalities can be enabled on each port.
For the Qlogic CNA cards, partition three can be set to either
NICMode
or
IscsiOffloadMode
.
Partition four can be set to either
NICMode
or
FcoeOffloadMode
.
Invoke the SetAttribute() method with the following parameters (from Section 15.1) and syntax:
Target: FQDD attained through
DCIM_NICEnumeration
AttributeName: Attained from
AttributeName
field
AttributeValue: A new value to assign to the specified
NICAttribute
. If this value is valid, it is
applied to the
PendingValue
property or the
Currentvalue
property of the specified
NICAttribute
. Possible choices are attained from
PossibleValues
field, such as:
Possible values: Disabled, Enabled
EXAMPLE:
wsman invoke -a SetAttribute http://schemas.dmtf.org/wbem/wscim/1/cimschema/
2/root/dcim/DCIM_NICService
?SystemCreationClassName=DCIM_ComputerSystem,
CreationClassName=DCIM_NICService,SystemName=DCIM:ComputerSystem,
Name=DCIM:NICService
-h $IPADDRESS -V -v -c dummy.cert -P 443
-u $USERNAME -p $PASSWORD -J SetAttribute_CNA_IscsiOffloadMode.xml
-j utf-8 -y basic
The information in the input file SetAttribute_NIC.xml is shown below:
<p:SetAttributes_INPUT
xmlns:p="http://schemas.dmtf.org/wbem/wscim/1/cim-
schema/2/root/dcim/DCIM_NICService">
<p:Target>NIC.Integrated.1-1-1</p:Target>
<p:AttributeName>IscsiOffloadMode</p:AttributeName>
<p:AttributeValue>Enabled</p:AttributeValue>
</p:SetAttributes_INPUT>
OUTPUT:
<n1:SetAttribute_OUTPUT>
<n1:Message>The command was successful</n1:Message>
<n1:MessageID>NIC001</n1:MessageID>
<n1:RebootRequired>Yes</n1:RebootRequired >
<n1:ReturnValue>0</n1:ReturnValue>
- Interface Guide for Linux 1
- Revisions 2
- Contents 4
- Executive Summary 14
- 1 Introduction 15
- 2 References 16
- 3 Overview 17
- StartTime, Until 18
- TIME_NOW 18
- 3.2.5 Return Values 19
- 3.2.6 Glossary 19
- 4 Discovery 20
- DCIM_iDRACCard 23
- UserName 25
- DCIM_iDRACCardString 25
- Users.4#Password 27
- CIM_Account 28
- EnabledState 28
- CIM_Privilege 32
- ActivityQualifiersSupported 34
- EnumerateEPR 35
- UserPassword 37
- ActivityQualifiers 39
- 6 Firmware Inventory 41
- 7 Firmware Update 43
- InstallFromSoftwareIdentity 45
- 7.5.5 Delete Job 47
- 7.8 CreateRebootJob() 51
- 7.9 Automatic Updates 52
- 7.9.3 Set Update Schedule 53
- 8 Power State Management 59
- 8.3.1 Base Server Method 60
- PowerStatesSupported 62
- CIM_PowerManagementService 62
- PowerChangeCapabilities 62
- 8.4 Power Control 63
- CIM_ComputerSystem 64
- 9 Hardware Inventory 65
- 9.2 Fan Inventory 66
- 9.3 Memory Inventory 67
- 9.4 CPU Inventory 67
- DCIM_CPUView 68
- 9.5 iDRAC Card Inventory 69
- 9.6 PCI Device Inventory 69
- 9.7 Video Inventory 70
- NICString 71
- NICInteger 71
- NICView 72
- 10 Job Control Management 77
- 10.2.2 Delete Job Queue 78
- DCIM_OSDeploymentService 81
- CIM_RegisteredProfile 81
- MessageID 85
- 11.3.5 Check Job Status 86
- 11.3.6 Boot to Network ISO 87
- 11.3.8 Boot To PXE 89
- DisconnectNetworkISOImage 93
- 11.3.16 Skip ISO Image Boot 95
- LastSystemInventoryTime 101
- Part Firmware Update 101
- Part Replacement 101
- 12.2.1 Create Config Job 102
- 12.2.3 List All LC Jobs 103
- ReInitiateDHS 106
- DCIM_LCService 106
- CurrentValue 108
- DCIM_LCEnumeration 108
- 12.14 ExportCompleteLCLog() 114
- 12.17 System Decommission 118
- 12.22 Remote Diagnostics 122
- DCIM_OpaqueManagementData 125
- CreatePartition 125
- DCIM_PersistentStorageService 126
- InitializeMedia 126
- CIM_ConcreteJob 126
- DCIM_VFlashView 126
- InstanceID 126
- Disk.vFlashCard.1 127
- 13.4 Create Partition 128
- PartitionIndex 130
- HashType 130
- 13.6 Delete Partition 131
- 13.7 Format Partition 132
- 13.8 Modify Partition 133
- 13.9 Attach Partition 134
- 13.10 Detach Partition 135
- BootConfigSetting 139
- BootSourceSetting 140
- ChangeBootOrderByInstanceID 140
- CurrentAssignedSequence 141
- ChangeBootSourceState() 142
- NICEnumeration 144
- DCIM_NICString 145
- DCIM_NICInteger 146
- DCIM_NICView 147
- DCIM_NICCapabilities 148
- DCIM_NICStatistics 149
- CreateTargetedConfigJob() 150
- RebootJobType 151
- DCIM_NICEnumeration 152
- IscsiOffloadMode 153
- OUTPUT: 155
- 15.14 Setting CNA LAN Modes 156
- 16 RAID Storage Management 160
- DCIM_RAIDInteger 162
- RAIDInteger 162
- DCIM_RAIDString 164
- RAIDString 164
- DCIM_ControllerView 165
- ControllerView 165
- PhysicalDiskView 167
- VirtualDiskView 168
- EnclosureView 169
- HotSpare 170
- ResetConfig 170
- ClearForeignConfig() 171
- DeletePendingConfiguration() 173
- 16.16 Managing Hot-Spare 173
- DCIM_PhysicalDiskView 174
- & & 178
- < < 178
- > > 178
- “ " 178
- MediaType 180
- VDRAIDEnumArray 181
- VDPropArray 182
- VDPropValueArrayIn 182
- VDPropNameArrayIn 182
- ObjectStatus 183
- VDPropNameArray 184
- 256KB = 512 512KB = 187
- 1024 1MB = 2048 187
- Attributes 191
- SetAttributes 193
- AttributeName 193
- PossibleValues 193
- ConvertToNonRAID() 195
- DCIM_BIOSEnumeration 196
- BIOSEnumeration 196
- BIOSInteger 199
- BIOSAttribute 202
- BIOSPassword 204
- ShareType 206
- 18.2 Automatic Backup 208
- 18.2.2 Set Backup Schedule 210
- 19 iDRAC Configuration 214
- DCIM_iDRACCardEnumeration 215
- DCIM_iDRACCardInteger 220
- IPChangeNotifyPS 225
- DCIM_LCAttribute 225
- 20 Remote Service Status 227
- 21 System Information 230
- 22 Sensor Information 232
- FCStatistics 234
- FCInteger 235
- FCEnumeration 236
- 23.9 Listing the FC Views 239
Produits connexes et manuels pour Logiciel Dell Lifecycle Controller 2 Version 1.3.0
Logiciel Dell Force10 Z9000 Manuel d'utilisateur
(937 pages)
(937 pages)
Logiciel Dell Vizioncore Manuel d'utilisateur
(141 pages)
(141 pages)
Logiciel Dell Brocade 300 Guide de l'utilisateur
(666 pages)
(666 pages)
Logiciel Dell Chassis Management Controller Version 1.0 for PowerEdge VRTX Guide de l'utilisateur
(155 pages)
(155 pages)
Logiciel Dell v1.1 Manuel d'utilisateur
(175 pages)
(175 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.025 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels