Dell PowerEdge T300 Manuel d'utilisateur Page 77
- Page / 194
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Installing System Components 77
Installing a Non-Redundant Power Supply
1
Slide the power supply into the back of the chassis until the power supply
release tab snaps into place (see Figure 3-10).
2
Replace the screw to secure the power supply to the system (see
Figure 3-10).
3
Connect all power cables to the system board, drives, and SAS backplane
(if installed).
Ensure that all power cables are routed properly to prevent the cables from
becoming pinched or crimped.
4
Replace the processor airflow shroud (see "Installing the Processor Airflow
Shroud" on page 72).
5
Replace the system cover (see "Installing the System Cover" on page 67).
Hard Drives
NOTICE: Combining SATA and SAS hard drives in the same system configuration is
not supported.
Depending on your system configuration, your system supports up to four
3.5-inch SATA or SAS hard drives installed internally (see Figure 3-13) or at the
front of the system (see Figure 3-11). Hard drives installed in your system are
connected to the system board, an optional controller card, or to the SAS
backplane (requires a SAS controller card). Only hard drives installed in the hard
drive bays at the front of the system can be used as hot-pluggable.
Removing a Hot-Pluggable Hard Drive
1 Remove the front bezel (see "Removing the Front Bezel
" on page 63
).
2
From the RAID management software, prepare the drive for removal a
nd
wait until the hard drive indicators on the front of the drive carrier signal
that the drive can be removed safely.
See your SAS/RAID controller
documentation for information about hot-pluggable hard drive removal.
If the hard drive is online, the green
activity/
fault indicator flashes as the
drive is powered down. When both drive indicators are off, the drive is
ready for removal.
book.book Page 77 Sunday, June 21, 2009 10:04 AM
- Dell™ PowerEdge™ T300 Systems 1
- Hardware Owner’s Manual 1
- Notes, Notices, and Cautions 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 8 Contents 8
- 10 Contents 10
- About Your System 11
- 14 About Your System 14
- Connecting External Devices 16
- Power Indicator Codes 17
- NIC Indicator Codes 18
- LCD Status Messages 19
- 20 About Your System 20
- 22 About Your System 22
- NOTE: The LCD continues 22
- 24 About Your System 24
- 26 About Your System 26
- 28 About Your System 28
- Removing LCD Status Messages 29
- System Messages 30
- 32 About Your System 32
- 34 About Your System 34
- 36 About Your System 36
- 38 About Your System 38
- Warning Messages 40
- Diagnostics Messages 40
- Alert Messages 40
- Responding to Error Messages 41
- System Setup Options 43
- Memory Information Screen 45
- CPU Information Screen 46
- SATA Configuration Screen 47
- Integrated Devices Screen 48
- Serial Communication Screen 49
- System Security Screen 50
- Exit Screen 52
- Using the System Password 53
- Using the Setup Password 56
- Entering the BMC Setup Module 58
- BMC Setup Module Options 58
- Recommended Tools 60
- Inside the System 60
- Front Bezel 62
- Removing the Front Bezel 63
- Installing the Front Bezel 64
- Front Bezel Inserts 65
- System Cover 66
- Installing the System Cover 67
- EMI Fillers 68
- Processor Airflow Shroud 69
- 7 cable guides (4) 72
- Hard Drives 77
- Removing a Cabled Hard Drive 80
- Configuring the Boot Device 84
- Diskette Drive (Optional) 84
- Installing a Diskette Drive 86
- 1 shoulder screws (4) 87
- Optical and Tape Drives 88
- 1 screws (3) 92
- Expansion Cards 93
- Installing an Expansion Card 95
- SAS Controller Card 96
- RAID Battery 99
- Installing System Components 100
- Installing a RAID Battery 102
- Removing the RAC Card 102
- Installing a RAC Card 104
- Cooling Fans 107
- Removing the System Fan 109
- Installing the System Fan 110
- System Memory 111
- Removing Memory Modules 112
- Installing Memory Modules 113
- Processor 115
- Installing the Processor 118
- System Battery 119
- Chassis Intrusion Switch 121
- SAS Backplane 125
- Control Panel 127
- System Board 129
- Installing the System Board 131
- Troubleshooting Your System 133
- Checking the Equipment 134
- Troubleshooting a USB Device 138
- Troubleshooting a NIC 140
- Troubleshooting a Wet System 141
- Troubleshooting a Fan 145
- Troubleshooting System Memory 146
- Troubleshooting a Hard Drive 153
- System Diagnostics Features 163
- Using the Custom Test Options 165
- Selecting Diagnostics Options 166
- Jumpers and Connectors 167
- 168 Jumpers and Connectors 168
- Jumper Settings 170
- 172 Jumpers and Connectors 172
- 174 Jumpers and Connectors 174
- Getting Help 175
- 176 Getting Help 176
- Glossary 177
- 178 Glossary 178
- 180 Glossary 180
- 182 Glossary 182
- 184 Glossary 184
- 186 Glossary 186
- 188 Glossary 188
- Numerics 189
- Index 191 191
- Index 193 193
Produits connexes et manuels pour Matériel informatique Dell PowerEdge T300
(92 pages)
(50 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.816 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels