Dell OpenManage Server Administrator Managed Node for Fluid Cache for DAS Manuel d'utilisateur Page 137
- Page / 316
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
omconfig: Managing Components Using the Instrumentation Service 137
The output of the omconfig chassis remoteaccess or omconfig mainsystem
remoteaccess command lists each of the available configurations. The
following table lists the valid parameters:
Table 4-12. Parameters of omconfig chassis remoteaccess or omconfig mainsystem
remoteaccess
name=value pair 1
config=
name=value pair 2 Description
config=
additional
ipv4=enable | disable enable: IPv4 stack to load on iDRAC.
disable: IPv4 stack to flush on iDRAC.
ipv6=enable | disable enable: Enables IPv6 stack to load on
iDRAC.
disable: Disables IPv6 stack to unload on
iDRAC.
NOTE: This option requires license to
enable or disable ipv6. If the appropriate
license is not installed or has expired, the
system displays an error message. For
more information, see
The Dell License
Manager
at dell.com/support/manuals.
config=advsol characcuminterval=
number
number: Sets the character accumulate
interval in 5 millisecond intervals.
charsendthreshold=
number
number: Sets the number of characters.
BMC automatically sends a serial over
LAN data packet that contains the
number of characters as soon as this
number of characters (or greater) has
been accepted from the baseboard serial
controller into the BMC.
enableipmi= true | false true: Enables IPMI over LAN.
false: Disables IPMI over LAN.
enablenic=true | false true: Enables DRAC NIC.
false: Disables DRAC NIC
NOTE: The enablenic option is supported
only on PowerEdge
x
9
xx
systems that
have DRAC 5 installed.
- Command Line 1
- Interface Guide 1
- Notes and Cautions 2
- Contents 3
- 4 Contents 4
- 6 Contents 6
- 8 Contents 8
- 10 Contents 10
- 12 Contents 12
- 14 Contents 14
- Contents 15 15
- Custom Delimited Format (cdv) 15
- 16 Contents 16
- Introduction 17
- Glossary 18
- CLI Commands 19
- Primary CLI Commands 19
- Primary CLI 20
- Success Messages 21
- Failure Messages 22
- Introduction 23 23
- Command Syntax Overview 24
- 26 Introduction 26
- Using the omhelp Command 27
- 30 Using the omhelp Command 30
- <command level 2> -? 39
- Commands 41
- Parameters Description 44
- PowerEdge yx2x systems 48
- Critical 49
- Administrator 60
- Commands for Viewing Logs 71
- Remote Access Information 86
- Processor 86
- Memory Array 87
- Firmware 87
- Network Data 88
- Storage Enclosures 88
- Example Command Output 89
- NOTE: You cannot change 95
- (continued) 102
- NOTE: The 107
- Description 127
- NOTE: This option is 133
- Management Guide 135
- The Dell Licensing 135
- The Dell License 137
- Manager 137
- NOTE: extipmiusergroup 148
- Usage of dracusergroup=custom 149
- Command Result Description 156
- Defining Alert Actions 158
- Available Alert Actions 159
- Event Name Description 160
- Commands for Clearing Logs 163
- Action Description 165
- Severity 170
- Example Recovery Commands 172
- Example Shutdown Commands 173
- Ownership Values 177
- Adding Lease Information 183
- Adding Outsource Information 186
- Adding Owner Information 188
- Adding Support Information 190
- Adding System Information 192
- Adding Warranty Information 193
- Using the Storage Management 197
- Command Elements 198
- Syntax Description 199
- Command 201
- Command Level 3 Use 201
- 202 omreport storage Commands 202
- NOTE: If a physical disk 203
- Replacing 203
- 204 omreport storage Commands 204
- Required 205
- Command Levels 205
- (1, 2, 3) 205
- 206 omreport storage Commands 206
- Required Command Levels 207
- 208 omreport storage Commands 208
- Required Command Levels (1 209
- 2, 3) and name=value pair 209
- 210 omreport storage Commands 210
- NOTE: This command is not 211
- Required Command 212
- Levels (1, 2, 3) 212
- Optional name= 212
- 214 omreport storage Commands 214
- 216 omreport storage Commands 216
- 218 omconfig storage Commands 218
- Complete Syntax 220
- Example Syntax 220
- 232 omconfig storage Commands 232
- CAUTION: The 232
- 250 omconfig storage Commands 250
- Parameter Specification 258
- RAID 10) 260
- Omconfig Enclosure Commands 274
- degree Celsius: 279
- List (lst) 299
- Table (tbl) 300
- Index 303 303
- Index 305 305
- Index 307 307
- Index 309 309
- Index 311 311
- Index 313 313
- Index 315 315
- Index 316 316
Produits connexes et manuels pour Serveurs Dell OpenManage Server Administrator Managed Node for Fluid Cache for DAS
(52 pages)
Serveurs Dell 58260075 Fiche technique
(1 pages)
(1 pages)
Serveurs Dell 58259908 Fiche technique
(1 pages)
(1 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.058 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels