Dell OpenManage Server Administrator Version 7.0 Manuel d'utilisateur Page 227
- Page / 302
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
omconfig storage Commands 227
omconfig Pause Check Consistency
Use the following omconfig command syntax to pause a check consistency
while in progress. See the Dell OpenManage Online Help for more information
about Pause Check Consistency.
Complete Syntax
omconfig storage vdisk action=
pausecheckconsistency controller=id vdisk=id
where id is the controller ID and virtual disk ID as reported by the omreport
command. To obtain these values, type omreport storage controller to display
the controller IDs and then type omreport storage vdisk controller=ID to
display the IDs for the virtual disks attached to the controller.
Example Syntax
To pause a check consistency on virtual disk 4 on controller 1, type:
omconfig storage vdisk action=
pausecheckconsistency controller=1 vdisk=4
omconfig Resume Check Consistency
Use the following omconfig command syntax to resume a check consistency
after it has been paused.
Complete Syntax
omconfig storage vdisk action=
resumecheckconsistency controller=id vdisk=id
where id is the controller ID and virtual disk ID as reported by the omreport
command. To obtain these values, type omreport storage controller to display
the controller IDs and then type omreport storage vdisk controller=ID to
display the IDs for the virtual disks attached to the controller.
Example Syntax
To resume a check consistency on virtual disk 4 on controller 1, type:
omconfig storage vdisk action=
resumecheckconsistency controller=1 vdisk=4
- Command Line 1
- Interface Guide 1
- Notes and Cautions 2
- Contents 3
- 4 Contents 4
- Using the Instrumentation 6
- 8 Contents 8
- 10 Contents 10
- 12 Contents 12
- 9 Working With CLI Command 13
- 14 Contents 14
- Introduction 15
- New Features 17
- Command Prompts 18
- Primary CLI Commands 19
- Success Messages 20
- Failure Messages 21
- Command Syntax Overview 23
- Using the omhelp Command 25
- 28 Using the omhelp Command 28
- <command level 2> -? 37
- Commands 39
- Parameters Description 42
- PowerEdge yx2x systems 45
- Critical 47
- Administrator 58
- Commands for Viewing Logs 67
- <component name> 72
- Output Attributes Description 74
- Example Command Output 77
- System Attributes 82
- Remote Access Information 83
- Processor 83
- Memory Array 83
- Firmware 84
- NOTE: You cannot change 91
- NOTE: The 103
- (continued) 112
- NOTE: This option is 128
- Default Warning Thresholds 130
- NOTE: extipmiusergroup 143
- Command Result Description 151
- Defining Alert Actions 153
- Available Alert Actions 154
- Example Current Probe Actions 157
- Example Fan Probe Actions 157
- Commands for Clearing Logs 158
- Action Description 160
- Event Name Description 160
- Severity 164
- Example Recovery Commands 167
- Example Shutdown Commands 168
- Ownership Values 171
- Adding Lease Information 177
- Adding Outsource Information 180
- Adding Owner Information 181
- Adding Support Information 184
- Adding System Information 186
- Adding Warranty Information 187
- Using the Storage Management 191
- Command Elements 192
- Syntax Description 193
- 196 omreport storage Commands 196
- NOTE: If a physical disk 196
- Replacing 196
- 198 omreport storage Commands 198
- Required 199
- Command Levels 199
- (1, 2, 3) 199
- 200 omreport storage Commands 200
- Required Command Levels 201
- 202 omreport storage Commands 202
- NOTE: For SCSI controllers 202
- Required Command Levels (1 203
- 2, 3) and name=value pair 203
- 204 omreport storage Commands 204
- Report Commands 205
- NOTE: This command is not 205
- Required Command 206
- Levels (1, 2, 3) 206
- Optional name= 206
- 208 omreport storage Commands 208
- 210 omconfig storage Commands 210
- Example for SAS Controllers 212
- Command 225
- Optional name=value pairs 225
- Complete Syntax 226
- Example Syntax 226
- Example Syntax to reconfigure 234
- CAUTION: The 239
- 240 omconfig storage Commands 240
- For SAS Controllers 245
- Parameter Specification 248
- Description 248
- RAID 10) 250
- Omconfig Enclosure Commands 264
- degree Celsius, type: 269
- List (lst) 285
- Table (tbl) 286
- Custom Delimited Format (cdv) 287
- Index 289 289
- Index 291 291
- Index 293 293
- Index 295 295
- Index 297 297
- Index 299 299
- Index 301 301
- Index 302 302
Produits connexes et manuels pour Serveurs Dell OpenManage Server Administrator Version 7.0
(58 pages)
Serveurs Dell DR4100 Manuel d'utilisateur
(119 pages)
(119 pages)
Serveurs Dell R2 Manuel d'utilisateur
(34 pages)
(34 pages)
Serveurs Dell PowerEdge R720 Livre blanc
(17 pages)
(17 pages)
Serveurs Dell R2 Manuel d'utilisateur
(32 pages)
(32 pages)
© 2020, manymanuals.fr. Tous droits réservés | 0.132 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels