Dell Dimension 9200 Manuel d'utilisateur Page 6
- Page / 63
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
Beep Codes
Your computer might emit a series of beeps during start-up if the monitor cannot display errors or problems. This series of beeps, called a beep code, identifies
a problem. For example, beep code 1-3-1 consists of one beep, a burst of three beeps, and then one beep.This beep code tells you that the computer
encountered a memory problem.
Reseating the memory modules (see Installing Memory) may fix the beep code errors in the following table. If the problem persists, see "Contacting Dell" in
your Owner's Manual for instructions on obtaining technical assistance.
The following table lists beep codes for non memory related errors.
Memory modules are detected, but a
memory failure has occurred.
l If two or more memory modules are installed, remove the modules (see Removing
Memory), then reinstall one module (see Installing Memory) and restart the computer. If the
computer starts normally, continue to install additional modules (one at a time) until you
have identified a faulty module or reinstalled all modules without error.
l If available, install properly working memory of the same type into your computer (see
Installing Memory).
A possible graphics card failure has
occurred.
l Reseat any installed graphics card (see Installing a PCI Express Card).
l If available, install a working graphics card into your computer.
A possible floppy drive or hard drive
failure has occurred.
Reseat all power and data cables.
A possible USB failure has occurred.
Reinstall all USB devices and check all cable connections.
No memory modules are detected.
l If two or more memory modules are installed, remove the modules (see Removing
Memory), then reinstall one module (see Installing Memory) and restart the computer. If the
computer starts normally, continue to install additional modules (one at a time) until you
have identified a faulty module or reinstalled all modules without error.
l If available, install properly working memory of the same type into your computer (see
Installing Memory).
Memory modules are detected, but a
memory configuration or compatibility
error has occurred.
l Ensure that no special requirements for memory module/connector placement exist (see
Memory).
l Ensure that the memory you are using is supported by your computer (see Memory).
A possible expansion card failure has
occurred.
1. Determine if a conflict exists by removing a card (not a graphics card) and restarting the
computer (see Cards).
2. If the problem persists, reinstall the card that you removed, then remove a different card
and restart the computer.
3. Repeat this process for each card installed. If the computer starts normally, troubleshoot
the last card removed from the computer for resource conflicts (see Resolving Software and
Hardware Incompatibilities).
The system is operating in quick
resume mode.
l Press the power button
l Move the mouse
l Press any key on the keyboard
l Press any key on the optional MCE remote control
Another failure has occurred.
l Ensure that all hard drive and CD/DVD cables are properly connected to the system board
(see System Board Components).
l If there is an error message on your screen identifying a problem with a device (such as
the floppy drive or hard drive), check the device to ensure that it is functioning properly.
l If the operating system is attempting to boot from a device (such as the floppy drive or
hard drive), check system setup (see System Setup Program) to ensure the boot sequence
is correct for the devices installed on your computer.
Code
Cause
1-3-1 through 2-4-4
Memory not being properly identified or used
4-3-1
Memory failure above address 0FFFFh
Code
Cause
1-1-2
Microprocessor register failure
1-1-3
NVRAM
1-1-4
ROM BIOS checksum failure
1-2-1
Programmable interval timer
1-2-2
DMA initialization failure
1-2-3
DMA page register read/write failure
3-1-1
Slave DMA register failure
- About Your Computer 2
- Back View of the Computer 3
- Back Panel Connectors 3
- Advanced Troubleshooting 5
- Beep Codes 6
- Dell Diagnostics 8
- Drivers 9
- Before You Begin 11
- System Board Components 14
- Memory 15
- Installing Memory 16
- Cards 18
- PCI Express Cards 21
- Removing a PCI Express Card 24
- Drive Panels 25
- Drives 27
- Hard Drive 28
- Installing a Hard Drive 29
- Adding a Second Hard Drive 30
- Floppy Drive 31
- Media Card Reader 32
- Removing a Media Card Reader 33
- CD/DVD Drive 35
- Battery 36
- Power Supply 37
- Removing the Power Supply 38
- Installing the Power Supply 38
- Processor 39
- Installing the Processor 40
- I/O Panel 42
- Installing the I/O Panel 44
- Processor Fan 45
- Card Fan 46
- System Board 47
- Installing the System Board 48
- Specifications 50
- System Setup Program 53
- Boot Sequence 55
- Clearing CMOS Settings 57
- Flashing the BIOS 58
- Technical Overview 59
- DC Power Connector P1 61
- DC Power Connector P2 62
- DC Power Connect P4 62
- DC Power Connector P7 62
- DC Power Connectors P10 63
- DC Power Connector P12 63
Produits connexes et manuels pour Ordinateurs Dell Dimension 9200
(160 pages)
(117 pages)
(10 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.847 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels