Dell OptiPlex GX270 Manuel d'utilisateur Page 139
- Page / 178
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
IDE Drive Addressing
When you connect two IDE devices to a single IDE interface cable and configure them for the cable select setting, the device attached to the last connector on
the interface cable is the master or boot device (drive 0), and the device attached to the middle connector on the interface cable is the slave device (drive 1).
See the drive documentation in your upgrade kit for information on configuring devices for the cable select setting.
Your computer supports up to four IDE devices. Connect hard drives to the connector labeled "IDE1," and connect CD/DVD drives to the connector labeled
"IDE2."
Most IDE interface connectors are keyed for correct insertion; that is, a notch or a missing pin on one connector matches a tab or a filled-in hole on the other
connector. Keyed connectors ensure that the pin-1 wire in the cable (indicated by the colored stripe along one edge of the cable) goes to the pin-1 end of the
connector. The pin-1 end of a connector on a board or a card is usually indicated by a silk-screened "1" printed directly on the board or card.
IDE Drive Interface Connector
Hard Drive
1. If you are replacing a hard drive that contains data you want to keep, back up your files before you begin this procedure.
2. Shut down the computer through the Start menu.
3. Ensure that your computer and attached devices are turned off. If your computer and attached devices did not automatically turn off when you shut
down your computer, turn them off now.
4. Disconnect any telephone or telecommunication lines from the computer.
5. Disconnect your computer and all attached devices from their electrical outlets, and then press the power button to ground the system board.
6. Open the computer cover.
Removing a Hard Drive
NOTICE: When you connect an interface cable, do not place the colored stripe away from pin 1 of the connector. Reversing the cable prevents the drive
from operating and could damage the controller, the drive, or both.
1
interface connector
2
colored stripe on cable
3
interface cable
CAUTION: Before you begin any of the procedures in this section, follow the steps in "Safety Instructions."
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of
your computer's electronic components. You can do so by touching an unpainted metal surface on the computer chassis.
NOTICE: To avoid damage to the drive, do not set it on a hard surface. Instead, set the drive on a surface, such as a foam pad, that will sufficiently
cushion it.
NOTICE: To disconnect a network cable, first unplug the cable from your computer and then unplug it from the network wall jack.
CAUTION: To guard against electrical shock, always unplug your computer from the electrical outlet before opening the cover.
- Abbreviations and Acronyms 2
- Advanced Troubleshooting 3
- Reinstalling Drivers 4
- Windows 2000 5
- Creating a Restore Point 6
- Before You Reinstall 6
- Reinstalling Windows XP 7
- Microsoft Windows XP 8
- Advanced Features 10
- Security 11
- Password Protection 11
- Assigning a System Password 12
- Typing Your System Password 12
- Setup Password 13
- System Setup 14
- Boot Sequence 15
- System Setup Options 16
- Booting to a USB Device 18
- Jumper Settings 18
- Power Button 19
- Hyper-Threading 19
- Power Management 20
- Battery 21
- Cleaning Your Computer 23
- Closing the Computer Cover 24
- Ergonomic Computing Habits 25
- Back to Contents Page 26
- Operating System CD 28
- Getting Help 29
- AutoTech Service 30
- Problems With Your Order 31
- Product Information 31
- Before You Call 31
- Contacting Dell 32
- Glossary 40
- DDR Memory Overview 47
- Installing Memory 48
- Removing Memory 50
- Regulatory Notices 51
- IC Notice (Canada Only) 52
- CE Notice (European Union) 52
- ENERGY STAR®Compliance 52
- VCCI Notice (Japan Only) 53
- Class A Device 54
- Class B Device 54
- BSMI Notice (Taiwan Only) 55
- SAFETY: General 57
- SAFETY: Battery Disposal 59
- PCI Cards 101
- Removing a PCI Card 103
- Serial Port Adapters 104
- Opening the Computer Cover 106
- Connecting Drive Cables 107
- Drive Interface Connectors 108
- Power Cable Connector 108
- Hard Drive 109
- Removing a Hard Drive 110
- Installing a Hard Drive 110
- Front-Panel Inserts 112
- Floppy Drive 112
- Removing a Floppy Drive 113
- Installing a Floppy Drive 114
- CD/DVD Drive 115
- Installing a CD/DVD Drive 116
- Cable Routing 117
- Microprocessor 119
- About Your Computer 124
- Back View 125
- Inside Your Computer 126
- System Board Components 127
- AGP and DVI Adapter Cards 129
- Adding a Second Hard Drive 142
- Removing a CD/DVD Drive 148
- Solving Problems 156
- Beep Codes 157
- System Lights 158
- Battery Problems 158
- Card Problems 158
- Drive Problems 159
- CD drive problems 160
- DVD drive problems 160
- Hard drive problems 160
- Dropped or Damaged Computer 161
- Error Messages 161
- General Problems 163
- A solid blue screen appears 164
- Other software problems 164
- Other technical problems 164
- General hardware problems 164
- Keyboard Problems 165
- Memory Problems 165
- Mouse Problems 165
- Network Problems 166
- Power Problems 166
- Printer Problems 167
- Sound and Speaker Problems 168
- System Board Problems 168
- Video and Monitor Problems 169
- Specifications 171
- May20048Y945Rev.A02 175
- Warranty and Return Policy 176
- Adding User Accounts 177
- Fast User Switching 178
- Network Setup Wizard 178
Produits connexes et manuels pour Ordinateurs Dell OptiPlex GX270
(3 pages)
(144 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.134 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels