Dell W-IAP103 Guide de l'utilisateur télécharger pdf (Page 226)

100

101

226 | show ap arm Dell Networking W-Series Instant 6.4.0.2-4.1 | CLI Reference Guide

60 0 0 0 93 0/0/0/0/94 0/0(0) 29/14//0/0(43)

64 0 0 0 93 6/0/0/0/94 0/0(0) 43/10//0/0(53)

149 0 0 0 93 3/2/0/0/99 0/0(0) 113/41//0/0(154)

153 0 0 2 93 23/23/0/1/100 0/0(0) 124/68//0/0(192)

157 0 0 0 93 2/1/0/1/94 0/0(0) 97/79//0/0(176)

161 0 0 5 93 3/2/0/0/99 9/0(9) 115/66//0/0(181)

165 0 0 0 94 10/10/0/0/100 0/0(0) 99/38//0/0(137)

1 0 0 12 78 60/50/3/0/79 8/0(8) 448/79//0/0(527)

6 0 0 0 78 12/11/0/0/81 0/0(0) 483/227//0/0(710)

11 0 0 8 78 71/54/3/16/86 0/0(0) 703/126//0/0(829)

Columns:util(Qual): ch-util/rx/tx/ext-ch-util/quality

HT Channel Summary

------------------

channel_pair Pairwise_intf_index

------------ -------------------

149-153 346

36-40 339

157-161 357

44-48 465

Interface Name :wifi0

Current ARM Assignment :161-/27

Covered channels a/g :1/0

Free channels a/g :7/0

ARM Edge State :disable

Last check channel/pwr :2m:36s/4m:24s

Last change channel/pwr :8m:19s/1d:23h:47m:12s

Next Check channel/pwr :2m:36s/2m:15s

Assignment Mode :Single Band

Interface Name :wifi1

Current ARM Assignment :1/24

Covered channels a/g :0/1

Free channels a/g :0/2

ARM Edge State :disable

Last check channel/pwr :5m:31s/3m:33s

Last change channel/pwr :15m:50s/1d:23h:47m:13s

Next Check channel/pwr :16s/2m:33s

Assignment Mode :Single Band

The output of this command includes the following information:

Column Description

channel

Displays the list of channels enabled on a W-IAP.

retry

Indicates the number of retry attempts.

Phy-err

Indicates the PHY errors on the current channels of a W-IAP.

Mac-err

Indicates the MAC errors on the current channels of a W-IAP.

noise

Displays the current noise level on each channel.

Util (Qual)

Displays the percentage of the channel being used and the current relative

quality of selected channels.

cov-idx(Total)

Displays RF coverage details. The W-IAP uses this metric to measure RF

coverage. The coverage index is calculated as x+y, where “x” is the W-IAP’s

weighted calculation of the Signal-to- Noise Ratio (SNR) on all valid APs on a

specified 802.11 channel, and “y” is the weighted calculation of the W-IAPs SNR

1 2 ... 221 222 223 224 225 226 227 228 229 230 231 ... 575 576

Dell W-IAP103 Guide de l'utilisateur Page 226

Commentaires sur ces manuels

Dell W-IAP103 Guide de l'utilisateur Page 226

Commentaires sur ces manuels

Produits connexes et manuels pour Points d'accès WLAN Dell W-IAP103